Jump to content
SAU Community

Rb26 Rb25 180sx S14 Sr20 Garrett Greddy T04z Td05 Drift Oem N1 Saas Parts Galore

toy515
 Share

Recommended Posts

toy515 Grand Master

toy515

Posted
Posted

n1 oil pump gears very good condition no marks $40

garrett turbo beanie few marks and rips on one side but cant notice once its on $70

dash 6 braided line 3 foot brand new $20

dash 10 braided line 3 foot brand new $20

t04z braided oil and water feed lines $30

t04z oil drain $20

td05 oil drains have 2 $10 each

greddy td05h-18g cores x2 suit rebuild $40 pair

gtr ecu back cover great for putting on power fc to make it look standard $20

r33 gtr front diff gears $30

r33 gtr knock sensor loom $40

drift silver polished oil cap $30

rb26 manifold heat shelids $30

rb26 water lines that sits under the twin turbo pipe $20

turbo oil and water lines (wrap around gtr turbos) pair $30

r33 gtr oil pressure switch $20

r33 gtr engine brackets suits all models $30

r33 gtr cam gears $20

r33 rb25 power steering pump in think its a non hicas one $20

r33 gtst brake pedal $20

s15 eye lids $50

hi octane s15 air diversion panel brand new $30

drift 3 inch stainless air filter brand new $20

saas 4 inch filter $20

4 inch unknown brand filter $15

5 inch canon muffler with a 2 bolt flange welded on $40

5 inch canon $30

5 inch canon $25

s14 engine minus intake manifold and cover suits rebuild $250

180sx turbo back 3.5inch exhaust $300

located on the gold coast

0421511710 will post all items

if you want pics sms me and ill send you a pic

kristafa Proficient

kristafa

Posted
Posted

might also take that power steering pump, i'm guessing you had that fitted to your 26..?

  • 3 weeks later...
RogueS13 Rookie

RogueS13

Posted
Posted

is there any gear left? if so, please pm me about the sr20

(p.s. joined the forum specifically for this!)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      It's been quite the ordeal but hey, at least you figured it out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...