Jump to content
SAU Community

Recommended Posts

FOR SALE

RB25DET SERIES2 ENGINE BRAND NEW

BOTTOM END HAS CP PISTONS, EAGLE RODS, ACL MAIN & ROD BEARINGS ARP HEAD STUD KIT ALL MACHINED TO SUIT. BLOCK HAS BEEN ACID WASHED, DIPPED, CRANK HAS BEEN HEAT TREATED, SCREWED ETC STILL UNASSEMBLED CAN ORGANISE ASSEMBLY.

AS FOR THE HEAD NEW EVERYTHING SOLID CAMS,FERRERA VALVE TRAIN - DOUBLE VALVE SPRINGS, RETAINERS, VALVE LOCKS, FERRERA VAVLES OVERSIZED, SOLID LIFTERS, VAVLE GUIDES HEAD ALL MACHINED TO SUIT AND HEAVILY PORTED & MATCH PORTED.

HAS 6BOOST MANIFOLD, WITH GARRETT TURBO GT42, TIAL WASTEGATE 100MM THROTTLE BODY WITH PLENUM.

ALL THAT IS NEEDED IS OIL & WATER PUMPS, FUEL RAIL & INJECTORS.

THOUSANDS AND THOUSANDS HAVE BEEN SPENT ON THIS.

GENUINE ENQUIRES ONLY

Link to comment
https://www.sau.com.au/forums/topic/338750-rb25det-race-engine-unfinished/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...

how much would you be willing to sell the head for, please text a reply to 0417670410

thanks bud

joel

FOR SALE

RB25DET SERIES2 ENGINE BRAND NEW

BOTTOM END HAS CP PISTONS, EAGLE RODS, ACL MAIN & ROD BEARINGS ARP HEAD STUD KIT ALL MACHINED TO SUIT. BLOCK HAS BEEN ACID WASHED, DIPPED, CRANK HAS BEEN HEAT TREATED, SCREWED ETC STILL UNASSEMBLED CAN ORGANISE ASSEMBLY.

AS FOR THE HEAD NEW EVERYTHING SOLID CAMS,FERRERA VALVE TRAIN - DOUBLE VALVE SPRINGS, RETAINERS, VALVE LOCKS, FERRERA VAVLES OVERSIZED, SOLID LIFTERS, VAVLE GUIDES HEAD ALL MACHINED TO SUIT AND HEAVILY PORTED & MATCH PORTED.

HAS 6BOOST MANIFOLD, WITH GARRETT TURBO GT42, TIAL WASTEGATE 100MM THROTTLE BODY WITH PLENUM.

ALL THAT IS NEEDED IS OIL & WATER PUMPS, FUEL RAIL & INJECTORS.

THOUSANDS AND THOUSANDS HAVE BEEN SPENT ON THIS.

GENUINE ENQUIRES ONLY

  • 2 weeks later...
  • 2 weeks later...
  • 1 month later...
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...