Jump to content
SAU Community

Recommended Posts

went out for an afternoon track session today at QR

have had the ME20 Pads in for 1 full and 3 half track days.

have been brutal on them the last 2 times out on the national circuit.

was about to head back out for the second afternoon session when a pair of black lines and some large 50c pieces of the pad material fell from the trailing edge of the backing plates of both front pads

The last inspection of the pads prior to the last half track day showed no cracking of the pad material and reasonable pad thickness.

gallery_56949_3979_457111.jpg

Link to comment
https://www.sau.com.au/forums/topic/340512-brake-pads-disintegrating/
Share on other sites

Endless W003 is the compound we use at Mallala - which is harder on brakes than QR - and no problems :D

went out for an afternoon track session today at QR

have had the ME20 Pads in for 1 full and 3 half track days.

have been brutal on them the last 2 times out on the national circuit.

was about to head back out for the second afternoon session when a pair of black lines and some large 50c pieces of the pad material fell from the trailing edge of the backing plates of both front pads

The last inspection of the pads prior to the last half track day showed no cracking of the pad material and reasonable pad thickness.

gallery_56949_3979_457111.jpg

Mark,

you've had a lot of rain up there recently, do you recall and instances where pads have bound to rotor (say overnight or if the car sits idle for a long period after rain?) you would hear/feel a noticable crack when you first move the car, or the car wouldnt move until you give it some throttle. I have a theory this happens a lot, and weakens the pad material, which then cakes off. Anyway, just a thought. I've never used ME20's, just the ccRG's (they have been fine).

Paul stokell diver training

I got a whole 15 min of drive time. :laugh:

Saw your car on the trialer heading out there! Looking very good :) It was the highlight of an otherwise pointless morning spent walking around in the bushes beside the cunniham highway lol

Saw your car on the trialer heading out there! Looking very good :D It was the highlight of an otherwise pointless morning spent walking around in the bushes beside the cunniham highway lol

So its you flashing passing motorists. :whistling:

How so Mark, Was there A lot of lecture time etc, or just too many peeps ?

Nah Noel I missed the first session as i was late from work and then the pads went after my first session out.

Didn't take a spare set of pads so called it a day.

Saw your car on the trialer heading out there! Looking very good It was the highlight of an otherwise pointless morning spent walking around in the bushes beside the cunniham highway lol

hope you weren't throwing rocks at it from one of the overpases!

Thanks,

Are u going to pirelli day on the 20th?

I might do those next year Drew. next track outings

- Lakeside 31st Oct (first time out there, really looking forward to it)

- QR 23rd Nov Round 6 Ruzic time attack series

Edited by handbrake

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few things that seem a bit off here. - why is there 2 BOV’s?  - the turbo smart BOV on the compressor housing, is it turned up ALL the way? I have seen this become an issue on old man Pete’s car. It would push open and recirc, turbo speed would rise and the boost pressure would do weird things. - stock head? Does that include springs? - tried a different MAC valve? Is it plumbed correctly?
    • Photo of manifold showing gate location? I mean, it's 6Boost, so we probably shouldn't be worrying, but always wroth knowing what the layout is. Plumbed back to atmosphere? Or into the dump?
    • Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
×
×
  • Create New...