Jump to content
SAU Community

Recommended Posts

P PLATE LEGAL TURBO! Mitsubishi Galant Vr-4 91’ For sale

This is what has been done to it.

The body has done 230000KM

I am looking for 7500

ENGINE FULLY REBUILT 3500km ago.

ACL Race Top and bottom engine bearings

RS Pistons and Rods

All Brand new Gaskets

Heavy duty Exedy Clutch 9 PUK 3500km old

Full 3 “ turbo back Exhaust

VAREX Muffler (controllable valve)

BC BR Coil over’s

Ostrich ECU chip

Palm Logger

EVO MAF

All Wiring done for a subwoofer and amp.

Pod Filter and shortened intake

Upgraded Intercooler.

Brand New Top Gun Leads

All Belts including timing belt done 3500km ago

Brand New Water Pump

Refurbished Gearbox

16G Rear housing of turbo.

EVO MAF

The interior is immaculate, and the body has been kept in excellent condition for its age.

Contact 0432358969 or Pm Me on SAU

The best part about this Galant, is that it is P plate legal. So if your looking to drive a turbo car on your p’s look no further! I have an exemption which i will gladly pass onto the new buyer. (Dont ask me 101 questions about the exemption and how you can get it for another car, because this is unique to this particular car!)

post-70346-1287382346_thumb.jpg

post-70346-1287382410_thumb.jpg

Edited by lanka05
I dont understand how you can "pass" the exemption onto the new buyer. A exemption is specific to an individual NOT the car it self...

Sorry mate, The new buyer will need to apply for the exemption. He/she can do it before purchasing the car.

Sorry mate, The new buyer will need to apply for the exemption. He/she can do it before purchasing the car.

I have an exemption which i will gladly pass onto the new buyer. (Dont ask me 101 questions about the exemption and how you can get it for another car, because this is unique to this particular car!)

Then don't provide false information.

You cannot pass on an exemption.

So it's NOT P-plate legal!

You need to be approved for an exemption. No different to any other turbo car, for P-platers. And they don't hand out these exemptions to anyone, you MUST have a special reason why you need to drive "high-powered" cars. ie: work related, etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...