Jump to content
SAU Community

Fs: Immactulate R32 Gtr Melbourne

anik3t

By anik3t,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

anik3t Contributor

anik3t

Posted
Posted (edited)

I reluctantly have for sale my cherished and much loved 1990 Nissan Skyline GT-R.

This car is in immaculate condition and very well looked after, it is a great example of a clean well modified GTR.

Company car on its way so this one must go. My loss is your gain.

ENGINE:

-Apexi Power FC + Boost Cont Kit

-Apexi Power FC Hand Controller

-HKS Twin Pods

-Splitfire Coil Packs

-Bosch Fuel Pump

-Greedy Adjustable Cam Gears

-Gates Racing Timing Belt (New)

-Greddy RB26 Clear Timing Case

-HKS Super Dragger Exhaust - Turbo Back - Split Dumps - High Flow Cats

-NGK Platnium Plugs (New)

-158,000 KMS

HANDLING + SUSPENSION:

-Nismo Shocks + Coilovers

-Nismo Control Arms

-Exeedy Heavy Duty Cushion Button Clutch

-17" Advan AVS Model 5's (New Rubber)

-Front & Rear Adjustable Strut Braces

-Bendix Ultimates Pads all round (New)

INTERIOR:

-Apexi Power FC Hand Controller

-Pivot Speed Meter / Speed Cut

-Apexi Boost Gauge - PSI -30 to +30

-2" Digital Tacho with Shift Light

-Blitz Turbo Timer

AUDIO + SECURITY:

-Alpine MP3/WMA Head Unit with iPod Cable

-Focal Fronts + Clarion Rear Speakers

-Sub/Amp Cables already wired

-Viper Alarm - Turbo Timer + Automatic Windows

SPARES:

-Original Air box + air guide

-Original R32 GTR Computer

This car has made 245awkw 0.9 bar boost on a safe tune.

Top quality oils used including Motul 300v Chrono and Redline.

New Battery, Alternator and Auxiliary belts installed on 16/08/10 (With Receipts)

Asking: $18,900 Negotiable

Location: Sanctuary Lakes, VIC

Feel free to contact me on 0432 326 666 or [email protected] if you have any questions.

Cheers,

Aniket

Note: The interior pictures have been taken without the genuine Nissan floor mats to show the condition of the original carpet.

Edited by anik3t
Link to comment
https://www.sau.com.au/forums/topic/340991-fs-immactulate-r32-gtr-melbourne/
Share on other sites
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...