Jump to content
SAU Community

Recommended Posts

Hi i'm relatively new to all this.

I've recently had a lot of interest in a manual 2003 V35 with about 94,000 kms on the dash.

A few people told me when it reaches 100k's it's going to need a timing belt change that's going to cost around 1000,

and some kind of special transmission oil that must be imported from japan, costing another 1000.

They have also told me that the seals on this car are extremely bad, and need constant refitting as they leak profusely.

Does anybody know anything about this, or the general maintenance costs of owning one of these?

Any input would be extremlyyyy helpful.

Cheers

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/341042-v35-maintenance/
Share on other sites

yup the timing belt should be changed at 100k. luckily for you the V35 doesnt have one, so you dont need to worry about it.

the transmission is easy, locally purchased fluid is fairly cheap.

its a car, just because its an import doesnt make it more expensive. however a lot of people that know nothing about them are scared and think imports are bad.

the V35 is a beautiful car, the engine is fantastic. Buy one in good condition, look after it and youll be fine.

Link to comment
https://www.sau.com.au/forums/topic/341042-v35-maintenance/#findComment-5504336
Share on other sites

Hi i'm relatively new to all this.

I've recently had a lot of interest in a manual 2003 V35 with about 94,000 kms on the dash.

A few people told me when it reaches 100k's it's going to need a timing belt change that's going to cost around 1000,

and some kind of special transmission oil that must be imported from japan, costing another 1000.

They have also told me that the seals on this car are extremely bad, and need constant refitting as they leak profusely.

Does anybody know anything about this, or the general maintenance costs of owning one of these?

Any input would be extremlyyyy helpful.

Cheers

VQ35DE uses a timing chain, whoever told you its a belt needs to lay off the grass.

Manual can just use any good brand of oil, its the 8 speed auto CVT in the 4 door that needs the special $1000 oil

Seals? the only thing which is a known issue seal wise with the VQ35DE is from memory oil can leak around the spark plug on the left bank, I think some sort of gasket/seal needs to get replaced. Don’t think this is too much of a major job just an inconvenience you may discover when changing the spark plugs

Link to comment
https://www.sau.com.au/forums/topic/341042-v35-maintenance/#findComment-5504340
Share on other sites

Hi i'm relatively new to all this.

I've recently had a lot of interest in a manual 2003 V35 with about 94,000 kms on the dash.

A few people told me when it reaches 100k's it's going to need a timing belt change that's going to cost around 1000,

and some kind of special transmission oil that must be imported from japan, costing another 1000.

They have also told me that the seals on this car are extremely bad, and need constant refitting as they leak profusely.

Does anybody know anything about this, or the general maintenance costs of owning one of these?

Any input would be extremlyyyy helpful.

Cheers

$2k for 100,000km's service?? I would rather have a M3 for that price.

I am doing my 90,000km's service tomorrow and going to ask what are the things and how much for them on a coupe for 100,000km's.

Will post up how much it cost me tomorrow.

Link to comment
https://www.sau.com.au/forums/topic/341042-v35-maintenance/#findComment-5504350
Share on other sites

Try not to get a 2003 model =S, they are prone to electrical problems such as windows failing and the radio/cd player screwing up. But then again u said it has 94,000km done so if it was going to have problems it would have happened by now or the previous owner has fixed them.

Link to comment
https://www.sau.com.au/forums/topic/341042-v35-maintenance/#findComment-5504408
Share on other sites

Seals? the only thing which is a known issue seal wise with the VQ35DE is from memory oil can leak around the spark plug on the left bank, I think some sort of gasket/seal needs to get replaced. Don’t think this is too much of a major job just an inconvenience you may discover when changing the spark plugs

Hi, related to the orginal post of maintenance, I was just told by my mech yesterday that my seals are leaking, oil leaking lower gasket and spark plugs oil seal leaking etc .. and i have to get a complete pair of the rocker covers to fix it??

Could you guys who have experienced/ fixed this leaking spark plug seal leaking problem before tell me more about it and what part numbers are the needed to fix a 350gt8 (VQ35DE)?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/341042-v35-maintenance/#findComment-5504947
Share on other sites

excellent! .. Thanks!

.. and wowcool .. the V series are great cars to own and drive, the GT8's CVT is the smoothest silk .. but just as you'll get extra attention on the road, you'll need to give it extra attention (ie research) when getting parts for it (unless you're happy to pay extra through nissan australia).

forums like this one is your source of help,

members like 180 wanabe makes a difference :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/341042-v35-maintenance/#findComment-5505600
Share on other sites

Hey Vic

Wat type of oil u using?? and where did u get it service at??

Hey Aaron,

I use Mobil 1 full synthetic oil and serviced at Fabcar.

I got my V from there and Nick, who works there, is a really good guy and takes good care of my V. He also drives a V35 coupe so he knows abit about the car too. :)

Edited by Victor.T
Link to comment
https://www.sau.com.au/forums/topic/341042-v35-maintenance/#findComment-5509096
Share on other sites

Mobil 1 is really good - used it a couple of times and produced some good results.

Aaron, if you want a discussion on oils - check this out:

http://www.skylinesaustralia.com/forums/Oi...-s-t320188.html

pretty much all types of oils for your V discussed on that thread.

Link to comment
https://www.sau.com.au/forums/topic/341042-v35-maintenance/#findComment-5509103
Share on other sites

Mobil 1 is really good - used it a couple of times and produced some good results.

Aaron, if you want a discussion on oils - check this out:

http://www.skylinesaustralia.com/forums/Oi...-s-t320188.html

pretty much all types of oils for your V discussed on that thread.

^+1 for the info.

To be honest, I don't know all the detail differences of the oil brands and their specifications. I just said I want the best they can offer, so I went with Mobil 1 from the start.

Edited by Victor.T
Link to comment
https://www.sau.com.au/forums/topic/341042-v35-maintenance/#findComment-5509117
Share on other sites

hi thanks again 180 wanabe, will those US G35 covers fit same as our JDM VQs?

... mmm those ss headers looks tempting :)

as for engine oil, i've tried mobil 1, royal purple and redline in the VQs ... i'm never touching mobil 1 ever again!

Edited by nissan rules
Link to comment
https://www.sau.com.au/forums/topic/341042-v35-maintenance/#findComment-5517418
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Kapr Haha yeah thats the one. I missed that you had a built up engine, I wouldn't want to run it on there either then. It was good in my situation just to replace the original turbo on a stock engine. @MBS206Yep definitely not a replacement for anything name brand
    • You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
    • https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
×
×
  • Create New...