Jump to content
SAU Community

Recommended Posts

Hey Guys,

Got something to rattle your brains here... i'll give you the back story though it may be unrelated...

on monday morning i got my air con regassed, it seemed to work fine. drove car for 10mins, stopped it for 5, got back in and drove for 15 mins to uni and everything seemed fine, air con was working.

i was at work at uni for like 5 or 6 hours.

come back to my car and it wont start, battery is half dead (lights on dash come up and it clicks). so i get it jump started from a friend. i wait there idling for a bit. it all seems fine, then the engine revs drop a bit, the hicas light comes on, then the engine dies.

i jump it again but the same happens again. i then disconnect the relay for the air con (thinking it's something to do with that)

i manage to drive it 10 mins home, but after i turn it off, i can't start it again, battery is dead.

i then get my house mates car to charge my battery for 10 mins, start mine up drive to petrol station, fill up, it starts again so i drive around for another 15 mins on roe hwy (thinking it would help charge the batt having the higher revs). i get home, park car, then this morning battery is completely dead again.

now, here is the confusing part.... i measure the current draw using a charged battery, and it says ~3.5-4A and nothing is on, keys aren't even in the IGN barrel. so i start removing fuses to try and track what is eating the power... i have now removed every fuse i can find (engine bay, driver's kick panel, near battery in boot) and it's still drawing ~3.5-4A!!!!

so has anyone every heard of something like this? or know anything else i can check?

(for reference, car is a 93 R33 4 door with RB25DET, pretty much no mods (no fancy alarm or other circuits wired in)).

Link to comment
https://www.sau.com.au/forums/topic/341070-unknown-current-draw/
Share on other sites

fog lamps are turned off (and fuse is pulled)

air con is disabled (no fuse or relay) as it was leaking anyways.

i was thinking aircon clutch, but yeah, i don't hear it.

thanks for the ideas guys, but no dice :)

ok, just for reference in case anybody else ends up searching for the same problem.... because i believe i have found it!

i started unplugging/ disconnecting things that connect to the main loom and use +ive... disconnected the starter motor, but that changed nothing.

but then as i took off the alternator, i saw sparks... once fully disconnected, current draw was 0.

so apparently my alternator is screwed... but i;ve not seen one die like this before. i will try taking it apart later and if i find more info i will post it here for future reference to others.

i was thinking aircon clutch, but yeah, i don't hear it.

Not hearing it is and indication it might be the problem, as it might mean its always on... try disconnecting it to see if the load disappears. Finding where to disconnect it might be tricky, you'll need to follow the wires. IIRC there's a plug but on mine it was near impossible to disconnect.

well, i was plugging and unplugging the relay for the clutch... so it should have been clicking on and off... or when i was connecting and disconnecting the battery. with the engine off it's pretty easy to hear anyways.

but yes, the plug for it is on top of the compressor, so you need to reach under the power steering pump and fumble blindly for a bit :thumbsup:

either way, going to source a working alternator and go from there.

if the larger white wire in the alternator plug has ignition supply then the alternator will be excited. pull the small plug off and see if the current draw drops. if not then must be alternator but if it drops then there must be a ignition relay or something stuck and sending power there with key off

right... well i noticed the spark from the lead which is bolted near the back, which i believe is output (ie, to the battery).

not sure about the alternator having power from somewhere else and being excited... i pulled out every fuse and relay in that car... ones in the boot, ones behind the kick panel and ones in the engine bay. i also undid all the plugs near the fuses in the boot (just in case) so the only place getting power was that connection point near the relays in the engine bay... so unless there is some other hidden relay somewhere else in the car...

hopefully i can get an alternator tomorrow and confirm that it was at fault... otherwise i will end up going insane trying to track this problem down.

the large cable on the back of the alternator is for charging the battery but alternator has a small plug with 2 wires to turn alternator on/off and for warning light. i would try disconnecting plug and seeing if it stops current draw before getting another alternator. i would have thought ignition supply to alternator would have come from fuse panel but the cables are quite large so prob a relay or fusible link

replaced alternator, haven't taken the car for a run yet, but it started ok and was running fine for like 5-10mins

it was also charging the battery which is a good sign.

just to note, there was a whining kind of noise which must have been from the alternator (i thought it was air related so i didn't think much of it) which i think one of the diodes in the rectifier have died hence the drawing current as it is now short circuiting through that diode.

will update with final result soon. am still thinking that the whole aircon involvement was coincidence.

  • 4 months later...

Yep, turned out to be alternator had a dead diode which was making a constant current draw.

alternator would still charge if you gave it enough RPM interestingly enough, it just wasn't as efficient.

So, 1 new alternator later and car has been good since then (except for the battery being old and dying, but thats another story)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...