Jump to content
SAU Community

Recommended Posts

Still got shite loads of parts that need to go CHEAP!!!

All from a BLACK standard and well looked after S2 R33 GTS-T

LH door complete, good condition no inside trim - $150

Bonnet slightly bent in RHF corner, easy fix - $50

LH Headlight faded - $20

Boot lid with original spoiler, good condition - $100

Good working sunroof - $100 if you remove it

Good Radiator - $75

Radiator Shroud - $25

ignition barrel & all locks with key - $200

Complete airbag setup (loom, control module, 2 airbags) - $150

Lots of inside trims for cheap

A/C compressor - $50

got all other AC components apart from the evaporator for cheap

Steering column - $50

have complete front and rear sub frames, all suspension components, diff, brakes, steering racks, control arms. selling all parts cheap - let me know what you need

Got all sorts of other bits and pieces lying around just let me know what your after.

Prices are Negotiable

I'm in Hornsby Sydney

Call me on 0418 672 182

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Still got shite loads of parts that need to go CHEAP!!!...

...LH Headlight faded - $20...

...Prices are Negotiable

Call me on 0418 672 182

Condition of LH Headlight besides the fog/yellow? brackets, lenses etc... can you PM me photos...

Best price posted to Melbourne 3073 (should be 10-15 bucks delivered)

Thanks, Ben 0422 782 888

Condition of LH Headlight besides the fog/yellow? brackets, lenses etc... can you PM me photos...

Best price posted to Melbourne 3073 (should be 10-15 bucks delivered)

Thanks, Ben 0422 782 888

apart from the faded lens the H/L is fine.

here's some pics

post-37988-1287888941_thumb.png

cant really see the mounts from this pic but they are all ok.

Let me know if you want it and i'll sort out postage.

hey mate just wondering if u have any of these parts

front bar headlights bonnet radiator radiator support

I have a bonnet that is slightly bent in the RHF corner, easy fix and cheap $50. I'll take some shots if you want.

The headlight is sold.

the radiator is pending payment, if anything happens I'll let you know

When you say radiator support, I have the vertical bolt on support that goes from where to bonnet latches on, to the bottom of the chassis. I think the horn is also mounted off it.

I don't have the horizontal piece, that needs to be cut from the car.

let me know if you want some shots.

Edited by hecticunt
What sorta spoiler did it have?

just the standard one raises up bout 4-5 inches off the boot, don't think it has a brake light on it or anything.

I can get a pic if your interested

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...