Jump to content
SAU Community

SAFC I Reset - help!

mupkant

By mupkant,
in Engines & Forced Induction

 Share

Recommended Posts

mupkant Enthusiast

mupkant

Posted
Posted

Hi guys,

Just installed SAFC I today by mechanics, dunno if they installed it correctly, since when i go into 'Monitor' --> '4 Channels' its shows the revs go up as i accerlate, also the air flow and correc. BUT NOT 'Trottle'

Throttle is always at 0% is this correct?

The main issue here is i want to reset the settings completely or change everything to value 0?

so that my car doesnt act so spastic, when i accerlate,

At the moment when i acceralte-moving to certain RPM's the car fully jerks (reminds me wen i first learnt manual) and sometimes the car seems like it will stall when dropping its REV's

Very dicculty to drive

Can some please help

where should i set the values to 0.

and dont say get it DYNOED as i will not untill i have an exhaust!!!

thanks

Link to comment
https://www.sau.com.au/forums/topic/34198-safc-i-reset-help/
Share on other sites
mupkant Enthusiast

mupkant

Posted
  • Author
Posted

when i change it to "04" "04" the cars rev starts droppin then the car turns off.

i figure '04' do to the table for my vechile. and i read the manual

"If. Sensor type is 'Hotwire' ...............

"if Sensor type is Pressure'...........

nothing beside it, looks like a bad pdf scan? a blur line in the pdf.

page 28 of the pdf

Link to comment
https://www.sau.com.au/forums/topic/34198-safc-i-reset-help/#findComment-685678
Share on other sites
predator Grand Master

predator

Posted
Posted

Yeah.. make sure you get the sensor type correct. I remember dicking around with that setting at one point. If its incorrect basically your engine check light will stay on and wont start. If you do a search on here you should be able to find out the base settings to at least be able to drive around until you get it dyno tuned.

THR should visible on the screen (% to full floor accelerator). Even if its just in ACC mode (e.g. not running), you should be able to press your foot to the floor and see the % THR change. If its not changing then its possible your mechanic forgot to connect the correct line to the ECU.

I've got an S-AFC I as well, so if you want the base settings and still having trouble PM me and I'll go turn my car on :P

Link to comment
https://www.sau.com.au/forums/topic/34198-safc-i-reset-help/#findComment-685810
Share on other sites
mupkant Enthusiast

mupkant

Posted
  • Author
Posted
Yeah.. make sure you get the sensor type correct. I remember dicking around with that setting at one point. If its incorrect basically your engine check light will stay on and wont start. If you do a search on here you should be able to find out the base settings to at least be able to drive around until you get it dyno tuned.

THR should visible on the screen (% to full floor accelerator). Even if its just in ACC mode (e.g. not running), you should be able to press your foot to the floor and see the % THR change. If its not changing then its possible your mechanic forgot to connect the correct line to the ECU.  

I've got an S-AFC I as well, so if you want the base settings and still having trouble PM me and I'll go turn my car on :)

omg Throttle % does not rise as i accerlate, only the airflow % & rev %

guess mechanic f*** the wiring? =

ill pop the ecu out later and take a look.

yes please with standard settings, just in case i left anything out

Link to comment
https://www.sau.com.au/forums/topic/34198-safc-i-reset-help/#findComment-686849
Share on other sites
mupkant Enthusiast

mupkant

Posted
  • Author
Posted
dont do it with the engine running...  just turn the key on until the reds come on in the dash...  perform the settings... turn the car off and then start it...

hehe thx,

i remember when i went to pick up my car, my hands got itchy so i played around with the settings, but was only meant to check the Monitors menu at the red lights.

somehow went to ETC and selected a wrong sensor

Revs dropped and my car stalled right in a Hwy (80 kph) road. :)

had to jump start it, as the battery was raped when trying to start it 20 times.

Link to comment
https://www.sau.com.au/forums/topic/34198-safc-i-reset-help/#findComment-686851
Share on other sites
neil_se Experienced

neil_se

Posted
Posted

When connecting my SAFC-I this week we noticed the manual doesn't actually tell you to connect the throttle wire. I had the SAFC-II manual as well and had to use that to wire the throttle. For some reason it only reads 85.8% foot flat to the floor though.

Link to comment
https://www.sau.com.au/forums/topic/34198-safc-i-reset-help/#findComment-686952
Share on other sites
predator Grand Master

predator

Posted
Posted

mupkant: went out to check my SAFC(1).. sensor type should be definitely "hotwire" (referring to the AFM I think). Check your voltages in "sensor check" while the engine is off. Sensor1: should be reading a reasonable value (around 1v or something). Sensor2: should be reading around 0v (mine was fluctuating between 0 - 0.1v). Again, THR voltage should increase as you put foot to the floor.

Definitely sounds like your problem is the lack of the THR line.. check the loom near your ECU to see whether its wired up.

neil:se -> go into the "sensor check" mode off "etc" and check the voltages.. mine at 100% THR (foot about 90% to floor) is about 4.35v. I'd check you're connections, maybe its dropping a bit of voltage due to dodgy solder job, etc. It could make a difference to overall effectiveness if the THR is out a bit.

Link to comment
https://www.sau.com.au/forums/topic/34198-safc-i-reset-help/#findComment-687120
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't think there's any way someone is push starting this car.. I honestly can barely move it, and moving it and steering it is just flat out not possible. I'm sure it is, but needs a bigger man than me. I have a refurbished starter now. The starter man was quite clear and consise showing me how nothing inside a starter really should contribute to slow cranking, and turned out that for the most part... my starter was entirely fine. Still, some of the wear items were replaced and luckily it didn't show any signs of getting too hot, being unfit for use, etc. Which is 'good'. I also noticed the starter definitely sounded different, which is a bit odd considering nothing should have really changed there.... Removed and refit, and we'll pretend one of the manifold bolts didn't fully tighten up and is only "pretty" tight. GM only wants 18ft/lb anyway. I also found a way to properly get my analog wideband reading very slightly leaner than the serial wideband. There's Greg related reasons for this. The serial output is the absolute source of truth, but it is a total asshole to actually stay connected and needs a laptop. The analog input does not, and works with standalone datalogging. Previously the analog input read slightly richer, but if I am aiming at 12.7 I do not want one of the widebands to be saying 12.7 when the source of truth is 13.0. Now the source of truth will be 12.65 and the Analog Wideband will read 12.7. So when I tune to 12.7 it'll be ever so slightly safer. While messing with all of this and idling extensively I can confirm my car seems to restart better while hot now. I did add an old Skyline battery cable between the head and the body though, though now I really realise I should have chosen the frame. Maybe that's a future job. The internet would have you believe that this is caused by bad grounds. In finding out where my grounds actually were I found out the engine bay battery post actually goes to the engine, as well as a seperate one (from the post) to the body of the car. So now there's a third one making the Grounding Triangle which is now a thing. I also from extensive idling have this graph. Temperature (°C) Voltage (V) 85 1.59 80 1.74 75 1.94 70 2.1 65 2.33 60 2.56 55 2.78 50 2.98 45 3.23 40 3.51 35 3.75 30 4.00   Plotted it looks like this. Which is actually... pretty linear? I have not actually put the formula into HPTuners. I will have to re-engage brain and/or re-engage the people who wanted more data to magically do it for me. Tune should be good for the 30th!
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      There are guys on Facebook under, Infiniti Owners Australia   https://www.facebook.com/share/g/1Z3RbPqx4k/?mibextid=wwXIfr What Whp are you after and I can help, and join this Q group in the states. https://www.facebook.com/share/g/19A59cN3JR/?mibextid=wwXIfr
    • MR51MN
      Who has a Infiniti Q60, Q50 (V37)?

      By MR51MN · Posted

      Does any of you guys have instagram pages for your builds? Keen to see some Aussie builds. I still can't figure out how to post photos in here.
    • MR51MN
      Who has a Infiniti Q60, Q50 (V37)?

      By MR51MN · Posted

      That awesome thanks for that. 
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      You can Remote any of these VR30..globally  Check: AMS Performance | Racebox | Sonic Tune | Soho | Z Motorsports | Specialty Z    Performance Parts | AMS | Z Motorsports | Boosted 6 |    Exhaust | Fast Intentions | ARK | MBRP Motordyne | Borla    There is someone in Sydney with 650whp   I am at 430whp without flex fuel, but FBO & Flex-fuel will push you to 500whp!!  
×
×
  • Create New...