Jump to content
SAU Community

V35 Sedan Wheels

rx3ip

By rx3ip,
in V Series (V35, V36, V37 & Infiniti)

 Share

Recommended Posts

VNS 24 Mentor

VNS 24

Posted
Posted
What is the widest size wheels to fit the 2004 V35 sedan and what offsets ? anyone can help ? I'm looking to buy 17" to fit the new car

17inch to 19inch x 9 wide, +32 offset all around with 255/35/- tyres should be near-perfect fit.

Fronts should be fine, but rears might stick outside the guard by 5mm to 8mm.

GoldV35 Enthusiast

GoldV35

Posted
Posted (edited)
17inch to 19inch x 9 wide, +32 offset all around with 255/35/- tyres should be near-perfect fit.

Fronts should be fine, but rears might stick outside the guard by 5mm to 8mm.

Correct on the fronts, but for the rear, 19x9.5 +45.

No lip rolling required, fits perfectly with 2 -3mm gap to spare.

See my pics for proof :blink:

Edited by GoldV35
VNS 24 Mentor

VNS 24

Posted
Posted (edited)
Correct on the fronts, but for the rear, 19x9.5 +45.

No lip rolling required, fits perfectly with 2 -3mm gap to spare.

See my pics for proof :)

Ok, nice. I didn't know you can get staggered rims on sedans. :blink:

Edited by Victor.T
rx3ip Explorer

rx3ip

Posted
  • Author
Posted

I got king springs ( KDFL-48 rear KDRL-49 ) fitted 2 days ago and the car lowered by more than 2" ... the bottom hit most of the sleeping cops at the shopping centre give me the shit

n15m0 .. where did you get the springs from and what brand ? I want to change the springs again to just lowered the car by 1"

I do not want 19" wheels because the ride will be too hard .. this is my daily driver

n15m0 Grand Master

n15m0

Posted
Posted

I'm running factory 350z struts and springs in mine. If you can find a low km used set get it. Best bang for buck mod I ever did.

Wife drives it as her daily nowadays carrying two kids, so trust me the ride is comfy as. If you are around my neck of the woods, I would be happy to take you out for a spin :D

GoldV35 Enthusiast

GoldV35

Posted
Posted
Hi goldv35

Is your car lowered at all , if yes by how much and what size tyres you run on front and rear ... your car looks very nice

Its lowered with the exact same springs you have, I do scrape sometimes but you get good at recognising whats too high and what isn't.

VNS 24 Mentor

VNS 24

Posted
Posted
I got king springs ( KDFL-48 rear KDRL-49 ) fitted 2 days ago and the car lowered by more than 2" ... the bottom hit most of the sleeping cops at the shopping centre give me the shit

n15m0 .. where did you get the springs from and what brand ? I want to change the springs again to just lowered the car by 1"

I do not want 19" wheels because the ride will be too hard .. this is my daily driver

I thought King Springs lower the car by 1 - 1.5 inch.

I might be wrong.

rx3ip Explorer

rx3ip

Posted
  • Author
Posted

I spoke to Kris from King Springs and he is going to make me new springs that is only lowered the car by 1" , cost slightly more .. now I'm up to 2 charges from my suspensions guy as he has to take out the springs again and install new ones including wheel alignment front and rear again .. I should have just install coil overs and adjust the ride height accordingly

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • bcozican
      WTAC 2025

      By bcozican · Posted

      i will be there 😁
    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Murray_Calavera
      WTAC 2025

      By Murray_Calavera · Posted

      Yeah mate, never miss it.
×
×
  • Create New...