Jump to content
SAU Community

Recommended Posts

I don't get it<

even if you did move em, couldn't you put em back on zero before you re install them?

I had the old style EL dash where you HAD! to remove the neddles to put them on , Very! tricky . If you have the new style where there is a bigger hole in the centre they can slide right over the neddle without having to touch them, MUCH ! MUCH ! better option , if you have the old style tell me and I may be able to help

old : small hole and anolog dial

new :big hole (about a 10c piece) and a digital touch type dial

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Top Posters In This Topic

That dont matter only n00bs type F5 all the l337 h4x0rs know it should be f5 and type that accordingly, n00bs!

Driftorie lite 1 , Mr "I was using my hand brake and it still won't slide" 0

I had the old style EL dash where you HAD! to remove the neddles to put them on , Very! tricky . If you have the new style where there is a bigger hole in the centre they can slide right over the neddle without having to touch them, MUCH ! MUCH ! better option , if you have the old style tell me and I may be able to help

old : small hole and anolog dial

new :big hole (about a 10c piece) and a digital touch type dial

Im not sure which ones?

will find out tomorrow I suppose.

If I have to pull em apart I'll get your help.

Driftorie lite 1 , Mr "I was using my hand brake and it still won't slide" 0

Yes I need practise cause I SUCK TOTALLY AND UTTERLY at drifting, so I am going to get more practise, still is Mr. "Doriftor Eliete" coming to the next drift day at QR like me?????

so is some one getting any thing under way fotr tomorrow night??? looking at Mr Mud & cyrus

Dont look at me, I have done my 1 cruise this week already :P

Anyway I am doing a parenting course that will run every second thursday night finishing bout 9:30pm and by that time you guys are already off gallavanting around the country side and now with no mobile it makes it hard to track you down, so meh I'll be a no show tomorrow if there is anything on.

Dont look at me, I have done my 1 cruise this week already :P

Anyway I am doing a parenting course that will run every second thursday night finishing bout 9:30pm and by that time you guys are already off gallavanting around the country side and now with no mobile it makes it hard to track you down, so meh I'll be a no show tomorrow if there is anything on.

hey cyrus I am looking into getting a new phone if ur keen I will be selling my old one for say $50 or a slab of bundy rum & colas comes with car kit & home charger & new 2nd battery

hey cyrus I am looking into getting a new phone if ur keen I will be selling my old one for say $50 or a slab of bundy rum & colas comes with car kit & home charger & new 2nd battery

Yeah sounds good, what is it?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...