Jump to content
SAU Community

Recommended Posts

bad news glenn

Wont find a grade 4.5 R32 cos it will be too old to get that grade, even if it was brand new.

Same problem, show me a compliancer who has the plates for one.

Cheers

Ken

true again.

but.. another 100 plates will be made available in the next 2 months.

my primary concern is still the engine though. dun wanna get a lemon and farked my fuel pump or afm @ 2am outside QUT.

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Top Posters In This Topic

true again.

but.. another 100 plates will be made available in the next 2 months.

my primary concern is still the engine though.  dun wanna get a lemon and farked my fuel pump or afm @ 2am outside QUT.

if u got a lemon no one will laugh cos u imported it...not like u could physically drive it before you bought it

but still... a lemon is an expensive fruit to cultivate.

true...but that's the risk with importing isn't it??

but in all seriousness, people have told me that the japs are very honest in their dealings with regards to exporting of cars and the car is evaluated properly so if there were any problems it will be stated...

so all you have to do is find some respectable people to import the car so they relay the information to you honestly and you should be all right

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...