Jump to content
SAU Community

Recommended Posts

Tomorrow its going in for water pump, timing belt and camgear at gavins. Must make sure i bring the right car down! as i don't drive the r33 to the goldcoast usually.

So I gather Gav made it back from the Dutton's rally in one piece? He was pretty excited about it!

Tell the boy's I said hello! I can't ring them all the time from my new job. I can't use the phone. Sucks! I bet they miss my harrassing phone calls but :)

:bs!:

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Top Posters In This Topic

yeah - i guess so.. not sure whether gavin or one of the other guys is doing it. I assume he has other guys to do stuff too ?

nex's one is in there now.. he's got a big bill though.

I better not get a big bill or i'll cry.

yeah - i guess so.. not sure whether gavin or one of the other guys is doing it. I assume he has other guys to do stuff too ?

nex's one is in there now.. he's got a big bill though.  

I better not get a big bill or i'll cry.

Gav won't be doing it.

Scott of Brett will. Both top guys.

Well Gav did the road tuning (he does all the tuning) and then fine tuned it on Matty Spry's dyno. Gav did most of the tuning but Matty did the economy tuning when I'm not up it. SO yeah, he did do some of it, but not a lot.

I hear he's a wizz at pfc tuning but. That's why gav goes there. It's easier for him to tune with someone who knows what they are dong as well

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • You don’t need to use full throttle all the time to break these blocks, 500kw at the wheels in more then enough to break them even with an occasional squirt. Hell I’ve seen them break under 400kw
    • A work around is to install the R35 card style AFM/MAF on the cold side of the intercooler piping and the BOV on the hot side piping. Works well, also you can combat the revs dropping by adding a bit more ignition timing on the idle ignition timing table to slow the rate of RPM drop.
    • Understood. If you dont have a ridiculous limit,  Tune, T's and P's are in check, and arent bashing it all the time and doing the due deligence for maintenance(inc oil analysis) then its pretty safe. 100% agree, let your right food control it to some extent.
    • So these external kits with the machined block for remote solenoid mount will only work on a NEO head and RB30 or RB26 bottom end   For an R33 head on a 26 bottom end the remote vct kit is to resolve RB26 manifold adaptor plates etc  IF you try to use the remote VCT on an RB30 or RB26 bottom end with an R33 head then  you can starve the cam journal??? I have one of these kits from bits I had years ago before plans changed  I don't understand how that tracks with this video   https://youtu.be/RuPiI22Mplk?feature=shared   This looks like I can run the v termite vct kit to feed the VCT on an R33 head on an RB26 bottom end?!?!?   Lol.... don't v have these problems on RB20s
    • Yeah i know that MAF is no no for this type of BoV. The engine has no BoV and "hose/pipes" ..it was all deleted (or probably it was not even on the engine when it was bought  ) It does that "sutututu" noise which i kinda do not want(atmospheric is better IMO...but standalone ECU)  What are the cons of running without blow off on stock RB25DET NEO. It running 5-7 PSI max (it has boost controller)   EDIT: and can Nistune be "tuned" to know there is no BoV to i dont know "know" and be better for a car? I read so many info about no BoV. One guy saying it is bad and hurting the turbo/engine/car and other that it does not...  
×
×
  • Create New...