Jump to content
SAU Community

Recommended Posts

Do RB26 (R32/R33 GTR) injectors fit into RB20 without any mods?

Not concered about resistence, as I am looking to do a ECU swap (most prob Microtech LT-12S or Wolf3d) which will allow me to run low-impedence injectors

Just want to know if the plug straight in without any mods, and if mods are required what where they

from memory they are around 440cc arent they?

Looking to make around 30rwkw more (200 at the moment) and don't want to run a regulator, so I would think that GTR injectors are more than capapble of this

Thanks heaps

Link to comment
https://www.sau.com.au/forums/topic/34332-gtr-injectors-into-rb20-question/
Share on other sites

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

thought about them, but for GTR injectors selling for around $300, they are a bit of a bargain for injectors that flow 440cc

440cc will be plenty for what power I am after, 550cc is a bit of a overkill I reckon. If I was going for a bigger turbo or chasing 300rwkw for sure, but for my bolt on RB20 440's will be fine

Just got to find out if they will fit thats all :cheers:

OUt of intrest, what do the RX injectors sell for?

If you are interested I have some (40,000km) stock R33 GT-R injectors for sale.

I am coming past Adelaide in 2 weeks, PM me

No probs, just gotta find out if they are going to fit first

I have a '92 R32 GTST with RB20DET, and if resistance isnt an issue with the ECU, then they bolt into place as though they were std RB20 injectors...and yeh if you dont need 550cc injectors then the 440cc GTR injectors seem to go for less than half the price.

Even if you are still running a std remapped ECU, the GTR Injectors WITH A resistance pack works fine and only took me about 4-6 hours to install and wire up...would have been quicker if i could have gotten the silly throttle body off!

cool, what about the injector plugs and such, do these need swapping or do the RB20 plugs fit? So its just a matter of pulling the old ones and dropping in the RB26 injectors?

Do you know if R32 GTR injectors differ from R33 ones?

Ok cool, sounds like they will fit without any drama's

Has anyone actually tried this combination of GTR injectors on a RB20, running Microtech/Motec/Autronic/Wolf3d ?

chris yes they will fit in no probs, and the plugs are even the same. Should work well, and not cause any probs with overfuelling at idel, the 550s can cause a little trouble with a stock rb20 and computer but any aftermarket management should handle the 550s fine, but they do however reqire the plugs to be changed, so get the gtr ones if you can find a nice set.

I am using 13B non turbo injectors which are either 420cc or 460cc Lol damn memory! Anyway I got them from a fella from nissansilvia.com for $35 each. They fit straight in, the last 4 digits are 1350 from memory??? Anyway I also, during the conversion got new injector plugs, which are similar to the stock ones except the lug is in the centre and not offset. They also have the spring you push down to unplug them vs the spring clip that gets flicked off and lost. I am running a microtech LTX12 (a 180sx RB20DET) and haven't got the car back yet so I cannot comment on the further.

Where do you get the resistor pack for them and how is it wired up?

I used the resistor pack from a GTR, so try ppl that are wrecking a GTR, or have half cuts etc etc. But in theory i cant think of any reason why you cant just go and buy 6 resistors from Jaycar and solder them in line. (I THINK the resistance of the GTR pack was 6.??ohms)

As for wiring them, if you are a confident DIY person who knows wiring diagrams and electrical circuits then it all to easy to do. If you dont, then it may be a little more awkward...

If you re going to be paying someone to do it then be sure they have done it before or know RB wiring backwards otherwise you will be paying a premium for them to learn on your car which doesnt make it such a cheap option when they want $500 to install. :thumbdwn:

chris yes they will fit in no probs, and the plugs are even the same.  Should work well, and not cause any probs with overfuelling at idel, the 550s can cause a little trouble with a stock rb20 and computer but any aftermarket management should handle the 550s fine, but they do however reqire the plugs to be changed, so get the gtr ones if you can find a nice set.

Sounds good mate, hopefully I will get some soon and get the ball rolling. Might need your help when it comes to fitting, I want to do most of the work myself but I know you have had injectors in and out of your RB20, so a bit of a watchful eye from someone who has done it before might be handy!

Will be re-doing the turbo to airfilter pipe as well, as I am doing away with the AFM, so will also drop by and get you to have a look at that

Hows the RB~? coming along? What type of managment are you going to run?

I used the resistor pack from a GTR, so try ppl that are wrecking a GTR, or have half cuts etc etc. But in theory i cant think of any reason why you cant just go and buy 6 resistors from Jaycar and solder them in line. (I THINK the resistance of the GTR pack was 6.??ohms)

As for wiring them, if you are a confident DIY person who knows wiring diagrams and electrical circuits then it all to easy to do. If you dont, then it may be a little more awkward...  

If you re going to be paying someone to do it then be sure they have done it before or know RB wiring backwards otherwise you will be paying a premium for them to learn on your car which doesnt make it such a cheap option when they want $500 to install.  :thumbdwn:

Im game enough to DIMyself but with the GTR resistor pack where is that located in the loom?

Im game enough to DIMyself but with the GTR resistor pack where is that located in the loom?

Physically the resistor pack is bolted to the right/drivers upright. It rectangular, about 80x30x45mm in size and is a ceramic resistor with a thin steel cover. It will have 6 blue wires going to it and one other wire, i cant remember the colour. Basically the 7th wire is the power wire whilst the 6 blue wires go to the injectors.

From a wiring diagram perspective the resistor pack goes between the power supply to the injectors and the +ve terminal of each injector

Physically the resistor pack is bolted to the right/drivers upright. It rectangular, about 80x30x45mm in size and is a ceramic resistor with a thin steel cover. It will have 6 blue wires going to it and one other wire, i cant remember the colour. Basically the 7th wire is the power wire whilst the 6 blue wires go to the injectors.

From a wiring diagram perspective the resistor pack goes between the power supply to the injectors and the +ve terminal of each injector

So what ill need to do would be to change the Gtst resistor pack to the GTR one? or is dont gtst have a resistor pack as such?

thanks Roy much apreciatted!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Sounds good Hmm suppose the main thing is, how much do you care about this car? The filler doesn't make for a very good water barrier lol. If there was a tiny little bit of rust forming now, that in 3 to 5 years time becomes obvious under the paint (starts to bubble up), would it bother you? 
    • I already have the ability to datalog the voltage... what I can't do is correlate it to what the gauge is showing when I'm looking at the data at a later date. Or something like this. Except getting the oil to 125C+ involves me going 200+kmh at the track so you can imagine this is a little tricky unless I do something like note what the voltage is when I am at the top of 5th gear so I have a point to reference on. Drove car today. O2 still reading richer because hopefully not a leak instead of massive restriction I've introduced. Car really doesn't sound like a LS. It's quite strange. Pulled a bit of fuel out up top. This does potentially explain why my spark plugs looked like the car was running pretty over-rich. If I was tuning it to a ~12.7 which in reality was far richer than that in the past. It will be handy to have the dyno WB to compare my WB to to compare notes that's for sure. At this point I'm happy to just sit in the passenger seat and tune the thing given I've got about 7 million hours on the platform lol.
    • Yeah I understand you have to pay for an updated map or subscription service or something. But I can't even find a current map for Australia. My map is dated 2017, but didn't this car version still sell in Australia until 2021?   Also, just as an aside, the navigation system warns you of traffic incidences ahead.....why would they include that on a map they knew is not receiving live information. I am forever going to be warned of an incident that probably existed for 30 minutes 8 years ago.
    • Car has been sold and I am now selling leftover parts. Prices are non-negotiable as I will sell to my mechanic if it won't sell here. Prices are firm except for the Random Parts listed at the very bottom. All parts are genuine except for the S-Tune front bumper. Volk Racing TE37SL 19×10.5″ +12 5×114.3 pressed graphite with P-Zero 275 30 19 tyres [USED] $4,500 Wheels are in perfect condition, have been sitting in my garage for the past 6 years. Tyres still have 90% tread, but since they're now old, I would not recommend you drive hard on them. K-Sport Super Sport External Reservoir Coilovers (made to order) [NEW] $2,500 Front spring rate 14kg, Rear spring rate 7.5kg Fork Type. You can read all about it here (https://www.k-sportracing.com/product_detail.php?Key=12). I was going to start tracking the GTR, but never got around to it. Paid $3500 (after USD conversion and taxes). HKS Kansai Service Tower Bar [NEW] $500 Never fitted in the original Japanese box. R34 GTR S-Tune Fibreglass Bumper [NEW] $500 No mesh - No Box - No damage - just dusty. Nitto RB26 Clear Timing Cover [NEW] $50 Couldn't fit RB2630 due to bonnet clearance. HKS Piping Kit Special Type (BNR34) & Apexi Power Intake Air Filter Kit & Password JDM Adapter [USED] $1,000 Missing some rubber hoses and supports, but you get what you see. Nismo NE-1 Weldina Turbo Back Exhaust & Custom 3.5"straight pipe [USED] $1,000 Needs some love, but perfect for those who want to go back to OEM+. Bayside Blue Aluminium Vspec Bonnet/Hood [USED] $700 Came off my GTR. Unfortunately, the tips have been slightly ground down. It will need some repairing. Bride Low Max Super Seat Rails [USED] $350 The price is for both sides. Will post pictures when I get a chance. Random Parts [USED] - negotiable Standard rb26 cams (intake and exhaust) $10 Stock amber front indicators $10 Standard GTR bumper lower side grills $10 Stock amber side indicators $10 Nismo Sports Resetting ECU $50 Water reservoir $10 Stock airbox mouth $10 Stock fuel rail $10 Stock coilovers from R34 GTR Vspec $100 PM me which items you are interested in. I do work 9-5, so I will be responding daily at best. Best time for pick up is after 5 and before 7 on weekdays, or i can work something out on weekends. I will only accept cash or PayID. Pick up only - located Epping NSW area.
    • sensible choice....and all 32s should be in yellow
×
×
  • Create New...