Jump to content
SAU Community

Recommended Posts

1995 Nissan Skyline GTS-T Coupe. Manual 6 cyl Turbo

2.5T 5 Speed Manual. Maroon.

152,868km.

work, parts and info for skyline r33 gtst

Nismo front grill, Hybrid front mount intercooler Custom 2.5in-3in intercooler piping, Stainless Blitz mesh 5in pod filter, 4in 90 deg alloy intake pipe filter to turbo, 40mm alloy radiator, Black silicone radiator hoses Carbing alloy radiator air deflector, 2x 12in thermo fans, Greddy Type R BOV 50mm, Garrett gt3540 ex gated with all speed flow fittings new and speed flow braided lines, HKS external gate 50mm, Custom intake plenum manifold ported and polished, New oil catch can, Splitfire coil packs, HKS Spark plugs, Turbosmart FPR, Ported and polished head, Tomei cams, Felpro SS valves, Tomei type b valve springs, Cometic multi layer metal head gasket, CP pistons/rings, Eagle conrods, ACL Race bearings, All gaskets are new on engine top to bottom, Jim Berry race clutch, 3 inch dump pipe with race cat, HKS hi power exhaust SS, EBC red stuff Brake Pads, Walbro hi flow Feul pump, Hicas rear steer lock bar, Work VR 10.5in rear 9in front light weight racing wheels wraped Federal 595 ss tyres 70 % tread, Tinted windows, Momo wheel, Greddy gear knob, Blitz turbo timer, Greddy profec b II boost controller, New VIPEC ecu, Pioneer head unit Pioneer splits front 6x9 pioneer rear 400w pioneer amp, Boost gauge and water temp gauges not fitted yet, All Dyno tuning By Mark @ Godzilla Motorsport. Currently still on run in tune 7PSI with 302rwhp, First part of run in was on dyno with mark bedding in rings with mineral oil dumped at end of 3 hour dyno tune and run with fresh mineral oil for another 1500km And run with HKS RB full synthetic oil Since approx 2-3000 km, has been meticulously looked after and serviced. Gear and diff oils changed 5000km ago.

plus more that have not remembered.

i Have reciepts for more than $20k spent

services every 5-10 k with only the best oils from Royal Purple, HKS and magnetic oil filters and sump plug for that little xtra protection.

A lot of TLC has gone into this project to make sure that it is a strong reliable but also powerful example.

i wont bullshit with numbers for expected kw/HP like some because i would hope it speaks for itself, but in saying that it was built to handle 25+ PSI Day in Day out .

ASKING $17,000 ONO

For More Information Please call Marcus on 0412622263

post-20616-1289212846_thumb.jpg post-20616-1289212876_thumb.jpg post-20616-1289212893_thumb.jpg post-20616-1289213142_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...