Jump to content
SAU Community

Recommended Posts

You won't find a digital copy of the owners manual in English..

You can buy a english printed version of the Manual from Import Driver for $59.00 CHEAP

Link to Manual

I have one for the R34 and it even has the service Recommendations in it and also covers all the R34 Models and GTR

Well worth the money with over 300 pages..

Edited by 99 GTT

My R34 Owners Manual is the official Nissan Manual in English distributed in the UK.

History:- Middlehurst Motorsport GT-R in St Helens, Merseyside was the main importer of GT-Rs in the 90s as an official GT-R Dealership.

I wouldn't know if they have any R33 Owners Manuals remaining but you can try...

www.middlehurst.co.uk or via [email protected]

Also trying the car club there in the UK > to strike the right person at the right time - this would be your best bet outside of e-bay or 99_GTT's link.

I have copy booting around somewhere that I can burn to disk and send you if pay for the disc and postage and buy me a beer some day...

or use a Torrent search as theres a downloadable version of the english printed version.

I'm after an English translation of the service (owners) manual, the one that comes in the cars glovebox - not the full 490 page workshop manual for an r33 gtst. I've got the big workshop one and after the other smaller one that comes standard in the glovebox.

I'm after an English translation of the service (owners) manual, the one that comes in the cars glovebox - not the full 490 page workshop manual for an r33 gtst. I've got the big workshop one and after the other smaller one that comes standard in the glovebox.

As I listed above if you click the Link.. It is about 300 half A4 pages. The stock the best approved printed not photocopied version for all the Skylines. (Printed in NZ)

Edited by 99 GTT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...