Jump to content
SAU Community

Changing Attessa Fluid, Run Into Some Problems. Help!

beRwick_GTRage

By beRwick_GTRage,
in General Maintenance

 Share

Recommended Posts

beRwick_GTRage Rising Star

beRwick_GTRage

Posted
Posted

hey everyone

recently finished putting an rb25neo into my r32 gts4. ive had the car running and idling but havnt driven it.

before i tried changing the attessa fluid the bottle in my boot and the rest of the system had no oil in it.

i folowed this DIY:http://www.skylinesaustralia.com/forums/R32-Gtr-Attessa-Fluid-t102731.html

filled the bottle with fluid, bled the nipple on the pump and unplugged the plug in the passenger footwell

but when i tried bleeding from the nipple on the back of the gearbox my attessa pump wouldnt start.

i also tried bleeding it with the engine running.

should i be able to hear the pump running?

my 4wd light is lit up on the dash.

any ideas?

thanks

doo doo Proficient

doo doo

Posted
Posted

The pump does turn off once it's reached a certain pressure in bleed mode (about 10 on the in- dash gauge in my car). It will start again once the pressure has dropped. It will also shut itself off after about 10 seconds (I think) of continual running to protect itself from burning out as it's not meant to run continuously. However, my 4WD light doesn't come on in bleed mode (R32 GTR) so check your attessa computer (in the boot parcel shelf?) to see if it's flashing any codes.

some_cs_student Veteran

some_cs_student

Posted
Posted

You should not need to have the car running, have you checked the fuses?

Once the ignition is on the ATTESA pump should start, only run it for a brief period of time before switching it off and giving it a break then repeat :rofl:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...