Jump to content
SAU Community

Recommended Posts

Hello all,

I'm going to be ordering a wideband O2 in the next 2 weeks and have found a really good price. Only really interested organising it for SA people as people will have to pick them up from me in Campbelltown, that way i don't have to stuff around with postage.

I have read a number of reviews and they are one of the best budget O2 sensor available. Generally they are around $250 mark. They also come with two gauge faces and two bezels so you can set them up to match your other gauges.

you can setup one of the output wires to simulate the factory Nerst cell (factory O2 sensor) signal so you can remove the factory O2 and just use the UEGO signal to control your ECU in closed loop.

Digital Wideband Air / Fuel Gauge

A wideband UEGO sensor controller accurately monitors Air/Fuel ratios (AFR) during the tuning process to prevent a lean fuel mixture, which could lead to engine damage. AEM has combined its single-channel wideband UEGO controller and gauge display into one unit, uniting unsurpassed AFR accuracy and control with an easy-to-read interface. AEM’s Gauge-Type Wideband UEGO Controller features a digital LED display and sweeping LED “needle” that changes colors as AFR changes from rich to lean. The unit’s 52mm (2-1/16”) gauge housing fits in most gauge pods and can be remotely mounted virtually anywhere.

  • Ideal AFR monitoring tool for EFI and carbureted applications, and engine dynamometers
  • Does not oscillate AFR reading like narrow band sensors
  • No laptop required for monitoring!
  • Bosch sensor included
  • Accurate to 0.1 AFR
  • Reads in AFR or Lambda via a switch in back of gauge housing
  • 24 Color-coded LED display lights provide immediate reference to engine’s air/fuel ratio (AFR) or Lambda ratio
  • Integrated three-digit display reveals AFR or Lambda in real time
  • User-programmable 0-5v analog output included for use with data loggers and virtually any engine management system
  • Serial data stream included for output of AFR (RS 232)

aemuegologo.jpg

Edited by heslo
Link to comment
https://www.sau.com.au/forums/topic/345742-wideband-o2-sensor-aem-uego/
Share on other sites

Seems to be just power and earth is needed, the Sensor just clips in to a loom and if you are going to use the Wide band to simulate the narrow band signal then there is one other wire than need to be wired in, but since your running a GTR you would need two so i would suggest getting the bung welded into the dump where the two front pipes meet.

Here's the manual;

AEM_UEGO_Wide_Band_AFR_Installation_Instructions_30_4100.pdf

Still looking for cheaper prices, it's looking like they will be at or around the $200 mark from Australia. Hearing back from a dealer in the next couple days.

Edited by D_Stirls

Ok Guys i have found a seller in Australia and The price is $200 and the order will be put in at the end of this week or the beginning of next. So if you want to get in on this PM me and i'll send you that bank details.

I would prefer to have people pick them up but if you really need it to be posted i'll put it in an express post bag (which i think is $15).

I found out that the reason the international sellers wouldn't send them overseas was because the warranty only covers the country they are sold in; so if i brought them in from the states they wouldn't have a warranty.

So these have a warranty as they are from an Australian seller.

Ok Guys i have found a seller in Australia and The price is $200 and the order will be put in at the end of this week or the beginning of next. So if you want to get in on this PM me and i'll send you that bank details.

I would prefer to have people pick them up but if you really need it to be posted i'll put it in an express post bag (which i think is $15).

I found out that the reason the international sellers wouldn't send them overseas was because the warranty only covers the country they are sold in; so if i brought them in from the states they wouldn't have a warranty.

So these have a warranty as they are from an Australian seller.

Apparently PM are down for the time being.

Just email me on; [email protected]

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Block bump. $400. As above cyl 6 needs bore or sleeve.
    • I would think making the argument that the travel is limited by a spring flexing against a spring perch as "the same method". Later on in the document they do state that the spring can't bind on full bump travel and cannot come loose in full rebound travel as well. (which is all very sensible). The laws are actually pretty sensible and reasonable. It's just that the people who enforce and check them don't actually read them or know them accurately. "Oh, coilovers? Instant fail mate. Don't even need to look at it." - Guy who will be instantly reported by me. There is probably merit to people who do get defected for height also get defected for the suspension in that state that allows it. I did never consider the people who are complaining about coilovers being picked on are also running around at 50mm off the floor.
    • I think given SAU's knowledge of E85 we can strongly conclude that 10% ethanol in almost any situation is entirely fine. Almost all of the myths against E85 were overblown, let alone E10.
    • From your link See bold text, is this referring to damper settings, if so that may a issue for "some" inspectors, I cannot see aftermarket coilovers having the evidence that "must be available that its functional performance is equivalent to the original" Maybe just remove the adjustment knows and hope for the best???? Meh 5.2 Suspension travel In all instances, modifications to a vehicle’s suspension must ensure the integrity of the system and not compromise the ride quality. At least two thirds of the original suspension travel should be maintained in both directions (rebound (i.e. extension) and bump (i.e. compression)), and rebound must be limited by the same method used by the vehicle manufacturer or if this is not practicable due to the nature of the modification, an equivalent method. If an alternative method is used, evidence must be available that its functional performance is equivalent to the original.
    • They actually don't - They adhere to VSB14 rules just like Victoria. The rules are against CABIN adjustable height, and it quite clearly states that the height has to be within parameters. I asked the VASS engineer to confirm this when I got my car engineered and they refused to engineer the coilovers because they didn't meet the requirements for requiring engineering. (mine are height adjustable.) People "Not wanting to bother" with "Actually reading/knowing/adhering to the rules" should result in fines and immediately losing the ability to issue blue slips and/or RWC's in Vic.
×
×
  • Create New...