Jump to content
SAU Community

Recommended Posts

Hi there,

My car is an R33.

I've looked but I cannot find any info.

I noticed the other day that when I flicked on the air con a red light came up on the right hand side of the dash. It had what looks like heat waves coming off a pipe like figure.

It only comes on when I turn the air con on. When I turn it off it disappears. Is it somethin to worry about? I wondered if it was some kind of exhaust sensor that has been disconnected when I had my 3" put in.

cheers,

Dan

Link to comment
https://www.sau.com.au/forums/topic/345789-red-light-on-dash/
Share on other sites

Sounds like the catalytic converter temperature warning light, PowerFC use it to indiciate engine knocking

Oh ok, would make sense because I took out the cat... being from NZ.

power fc uses the check engine light to indicate knock by flashing it several times in a short space of time

if its the cat convertor overheat warning then there may be a wiring issue or maybe it was just unplugged when something was done/replaced

power fc uses the check engine light to indicate knock by flashing it several times in a short space of time

if its the cat convertor overheat warning then there may be a wiring issue or maybe it was just unplugged when something was done/replaced

The light will come steady on and maybe flick off for a bit after a while, and then turn on again. I have a Z32 computer installed not a powerfc.

Yeah that's fine was just correcting the previous post.

That's a bit strange. The sensor should bring up a warning (that red light) when excessive temperature is noted in the cat. Sometimes this happens with a stock exhaust when the car dumps fuel into the engine at higher then normal boost levels. But since yours has a 3 inch exhaust I wouldn't think so

Sounds more like a wiring problem, or perhaps the sensor is old and as the wires heat up it's creating to much resistance, but again that doesn't explain why it's only doing it when you turn the air con on. Unless your z32 ecu is throwing to much fuel in when the air con is on, perhaps putting it into a rich and retard mode, I'm not sure.

Does the car drive ok when the ac is on and it does this? Maybe just check the sensor and wiring under the car just as a start. But it doesn't sound like anything to be concerned about

Yeah that's fine was just correcting the previous post.

That's a bit strange. The sensor should bring up a warning (that red light) when excessive temperature is noted in the cat. Sometimes this happens with a stock exhaust when the car dumps fuel into the engine at higher then normal boost levels. But since yours has a 3 inch exhaust I wouldn't think so

Sounds more like a wiring problem, or perhaps the sensor is old and as the wires heat up it's creating to much resistance, but again that doesn't explain why it's only doing it when you turn the air con on. Unless your z32 ecu is throwing to much fuel in when the air con is on, perhaps putting it into a rich and retard mode, I'm not sure.

Does the car drive ok when the ac is on and it does this? Maybe just check the sensor and wiring under the car just as a start. But it doesn't sound like anything to be concerned about

Hey thanks for the reply.

I will be seeing my tuner this weekend for other reasons, but I can check it out with him to see if it is the result of his tune. The car drove fine when i had it on A/C but I never really left it on for a long period once I had noticed it.

I don't even have a cat anymore so I would say that is nothing important also. It is just weird with the air con turning.

cheers,

Dan

probably just a wiring fault then. Might just be earthing the wire for the cat sensor when the AC compressor is cutting in and out or something. Just check to see what they did to the sensor when they replaced your exhaust

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sounds more like what Brad said, that it's mainly transfer. What pad bed in procedure did you use, and did you replace/machine the rotors, or just swap pads?
    • The stutter is almost entirely in the pedal. I don't feel the brakes release and reapply as you would with ABS engaging but the pedal feels that way, without the brakes releasing. It only lasts for less than a second and the pedal is fine again. It's hard to explain, sorry.  I'll get under this weekend and just double check everything is tight. Fluid is at max where I left it.
    • What bedding in procedure did you use?   When you say stutter, what exactly do you mean? Like it feels like someone letting go of the brakes momentarily and regrabbing them again to get you to stop? Re-reading your post, and that is what it kind of makes me think you're explaining, like theres a little bit of a jolt, likely just as you're reaching a stop. I've only had this issue once. And if its caused by what caused mine, you will want to get the car up on stands again and check it over. Mine was a case of a caliper mounting bolt coming out and letting the caliper rotate on the other remaining bolt and gave play in a wheel as it came to a stop. But not every stop either!
    • Yeop... binned it   This will be a summary will not many pics atm and cbf  Fixed the samsonas - it was totally munched Put a new precision 7675 T4 on with proper split pulse mani Got to Sydney to get to car - drove to canberra to get racecar - drive back to sydney that night Next day all day at Plasmaman putting on new clamps cleaning some things up and adding another large engine oil cooler sitting at the rear above diffuser to keep things cooler Next day - Tuesday - on Dyno - killer wikid awesome pumped out really good numbers - more mid range and on lower boost levels Wednesday - first prac - all day again getting the suspension right - had to borrow front suspension again - out do a lap come in - out do a lap - in - what i had just couldnt handle the load at the more consistent higher speeds - got a lap in at the end of the day that was pretty reasonable  Put it this way that lap wouldve had me in 4th in Pro am for the whole event - with only 700 hp and used tyres Thurs first official prac day - lap out warm up - then entered a hotlap with above setting and 80% effort took corners 1,2,3 and into 4 car felt awesome -  rear came around out of nowhere bang into the wall near front on at whatever 140 kmph Done, over, gone Just one of those how did that happen apparently as all indications show nothing out of the ordinary Got to spend the rest of the time at the event like I hadnt done before - was actually Ok mainly as I had my family and my boy is 9 and got treated like a rockstar Long trip home, lost a trailer wheel in nowhere land, X5 airbag suspension gave up half way across nullabour and rode on bumps stops (its now completely fine) had to do a 19 hr drive day on day 3 as accommodation got screwed up so just had to keep driving till found a town with some Now to reassess - hopefully the motor and other things are OK but yet to be seen too. There is no easy fix there is no i'll just order that part and get it sent - we'll have a talk to people see what can happen and what the go is but at minimum its rebuild from scratch struts forward and alot of time effort and $ should and if I return and if but maybe/ when  I have the cage tied into the front strut towers - if I didnt have that things couldnt been worse you can say its just a front end but if you know what goes into these cars... you'll know what that actually means in reality   Car was very fast. Disappointing we just didnt get to show it Effort doesnt win you races though     Apparently this is motorsport !  
    • Thanks, will do that.  Thankfully they still feel great.
×
×
  • Create New...