Jump to content
SAU Community

Recommended Posts

IMG00349-20101220-1026.jpg

pro_gtr21-img600x450-1289830612wuaqxv16708.jpg

R323.jpg

R32gtr.jpg

$149 for the above posted

5speed awd rb26dett trans+transfercase

awd oil pan

flywheel

clutch master

awd msic parts

r32 front spindels +200

R32 Tein gtr front coilovers +200

DSCN6184.jpg

harness

ecu

maffs

hks Fcon pro v harness

ecu stock r33 rb26dett

cas

coil packs

all above listed $399 shipped.

Link to comment
https://www.sau.com.au/forums/topic/348154-r33-r32-rb26dett-part-out/
Share on other sites

  • 2 weeks later...

IMG00369-20101228-1140.jpg

IMG00366-20101228-1140.jpg

IMG00367-20101228-1140.jpg

sorry trans sold and im in the USA, SO.cal

Fcon pro v harness is $149 shipped to AU

complete R33 GTR engine harness with all of the items in the post is $389usd + post is $85usd.

r u selling the doors to an if so how much an what car r they for

its for a 180sx but you know I'm not in Australia, I would only be able to ship it ocean freight total delivered to you is about $800usd for the doors and shipped to you

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...