Jump to content
SAU Community

Recommended Posts

Hi guys, here's the original photos re-uploaded to Flickr (stupid Webshots went down without as much as a warning...)

13970798536_d00f4e4af2.jpg
1. Stock front bar with old plates

13990694072_6948c20d9c.jpg
2. Trust vertical flow intercooler kit

13990695342_25a0a43b4a.jpg
3. Intercooler before tidying up

13990695732_a7aac7bf1c.jpg
4. Intercooler after tidying up

13970796796_5185c2a68b.jpg
5. Tools for tidying intercooler

13990717421_aea07abdd6.jpg
6. Box-o-nuts

13970802426_6dec900d55.jpg
7. Trial mount, compare FMIC size to stock SMIC on the right

13994336254_b0636c4c23.jpg
8. Trial mount of piping

14013895823_723467a5cd.jpg
9. Need clearance

13993897915_801f708b7c.jpg
10. Tools of the trade

13970797926_4c6728ea3b.jpg
11. Trimming the reo bar

13994335654_a4779ca244.jpg
12. Got clearance!

13970797186_cb76f5265a.jpg
13. Trimmed reo bar

13990693652_2fe78c317e.jpg
14. Hard piping, straight bolt-on

14013895863_db037ff39b.jpg
15. Reinstalled reo bar

13990718061_562f59af80.jpg
16. Front bar before cutting

13990693662_d6beefcc33.jpg
17. Front bar inside, the whole boxed section in the middle was removed

13990693112_2556d12eab.jpg
18. Almost done

13990692962_84b552fcb2.jpg
19. The finished product. Needs a good clean though!

Edited by V28VX37
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • would a r34 gtr hood line up with gt/gtt stock fenders? after latch, front bumper and hinges are swapped for gtr ones? or would the fenders be too low or high in relation to the hood surface? ( I believe seeing somewhere that gtr front fenders use some type of riser for the sides, but do not know how that relates to stock gt/gtt fenders.)    
    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
×
×
  • Create New...