Jump to content
SAU Community

Recommended Posts

the ones on the car arent for sale thats why :thumbsup:

i have both of the headlights that are listed for sale still though.

  • Replies 113
  • Created
  • Last Reply

Top Posters In This Topic

hi, yes i do have the front seatbelts.

Driveshafts

Rear brakes + hubs and knuckle

back section of handbrake cable

front rotors / calipers

all sold

  • 2 weeks later...

hey dont have one.

Set of Front LCA's gone

The rack/cross member that wasnt in the car has gone

1x power steering res gone

How much for f & r calipers, rotors, pads and lines and condition/type of all

Driveshafts

Rear brakes + hubs and knuckle

back section of handbrake cable

front rotors / calipers

all sold

no aftermarket dump pipe

i havent taken off the cable to open the petrol tank. i would have to check its condition for you though.

  • 3 weeks later...

ok the wreck has everything off it that i actually want/have sold. What ever is left on it is going super dirt cheap so if you can see anything tell me before it goes all together!

IMG_2986.jpg

IMG_2988.jpg

IMG_2987.jpg

IMG_2990.jpg

IMG_2989.jpg

IMG_2985.jpg

IMG_2991.jpg

IMG_2992.jpg

IMG_2994.jpg

all the panels are off the car now, make an offer!

IMG_2996.jpg

IMG_2997.jpg

still have the 18's and the 3.5" exhaust, manual tail shaft. Offers!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...