Jump to content
SAU Community

Recommended Posts

Hi,

I purchased a reasonably highly modified R33 GTR from Qld (I live in NSW). I received it yesterday after it was shipped down by TNT and then had to go through all the bs to get it registered. My local mechanic did the blue slip no probs, but when I went to the RTA to get it registered they told me that my car had been "flagged" as a high risk for rebirthing etc and I have to now get an RTA inspection on Thursday before they will register it. The lady told me that they would be focusing on engine numbers etc to ensure that the vehicle hasn't been rebirthed but my concern is the modifications. I have asked my mechanic to remove the oil catch can, guages on the a-pillar, hide the turbo timer and ebc etc. but it is very difficult to make the car look standard when you don't have any of the original parts such as the pod filters and big HKS exhaust.

Has anyone had one of these inspections before? Do they check through everything? I'm sure I will only be asking for trouble if I don't replace the exhaust and pod filters (and most of the other obvious stuff) but I don't see what choice I have. This is really stressing me because I have gone through a lot of hassles already to get the car and now the last thing I want would be to not be able to register it.

Thanks for any help.

Link to comment
https://www.sau.com.au/forums/topic/34899-rta-inspection/
Share on other sites

hey gtrrex... after i bought my car in sydney and brought it back to newcastle, went to transfer rego and the rta told me to go to the local pits for a identity check, which from what i saw they appeared to check engine no. chasis no. and they also checked the petrol filler for ULP only filler spout i suppose. At the time my exhaust was about 110dbs and i had a turbo timer, nothing was said, i did borrow a std air box for the inspection.

hope this helps and good luck !

Lenno

Link to comment
https://www.sau.com.au/forums/topic/34899-rta-inspection/#findComment-698123
Share on other sites

hehehe..just to add to it all! i went through the same thing...had my car brought here from melb and when trying to get it registered, i had to take it to the rta for a check...it was quite stressing cause they take your car into a warehouse area and close the door...so you can't see whats happenin...then they do all their checks and give you back your car...

like everyone has said, don't stress too much...they're just checking to see that the car isn't stolen or using stolen parts :D

Link to comment
https://www.sau.com.au/forums/topic/34899-rta-inspection/#findComment-698422
Share on other sites

Thanks for your responses!! I feel much better knowing that this is a common occurrance. The vibe I got from my mechanic when I told him I had to get an inspection was that I would more than likely have trouble with it.

Hopefully 11:30am on Thursday I will be the proud owner of a REGISTERED GTR!

Thanks again.

Link to comment
https://www.sau.com.au/forums/topic/34899-rta-inspection/#findComment-698508
Share on other sites

your oe of the unlucky ones, its only 50 percent of people that get asked to do an identity check, it has nothing to to with the car being flagged or anything like that, its just random, i was lucky to register my car without an identity check, but anyways like someone wrote on this thread if you knwo everyhthing is legal on the car you have nothing to worry about,

cheers mate and good luck on the test,

Link to comment
https://www.sau.com.au/forums/topic/34899-rta-inspection/#findComment-698905
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...