Jump to content
SAU Community

Recommended Posts

Hi Folks, my v35 300gt sedan is in bad need of some new shocks. So I was wondering if anyone on here knew what my options are. I heard the 350z shocks and coils fit, but I also read that they lower the car approx 1 inch. Normally this would be ideal, however this is my wife's car and she already complains about it scraping on big speed humps and spoon drains. While we don't want to lower it we do want to stiffen it up. Both of us prefer hard suspension.

So what are my options ?

Are the 350z shocks the same, but with lowered coils ? Or are the shocks actually different ?

Could I use G35 sedan shocks from the US ? Like these

http://cgi.ebay.com/ebaymotors/TOKICO-HP-Shocks-Struts-Infiniti-G35-Sedan-03-04-05-06-_W0QQcmdZViewItemQQfitsZModelQ3aG35QQhashZitem3cb3d2dc9fQQitemZ260714978463QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

or are there local options from the likes of bilstein or koni ?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/349043-v35-sedan-suspension/
Share on other sites

Hi,

I have just swapped the lowered springs in our 300GT over to 350Z springs due to it dragging everything over speed humps, etc and its now fine. Just go with standard height Z stuff.

There are pics here in the V section showing the difference between Z and factory springs on a sedan. Just do a search.

Cheers

Get some low mileage suspension from a 350gt-8.

Hello, I purchased a sports suspension (shocks and springs) from a 350GT-8 for my 300GT. The suspension actually raised the car by 10mm but improved the handling immmensely.

I had picked up some unrevised 350z springs but decided against using them as it would have lowered the car by at least 10mm and I was rubbing on to many driveways as it were.

The sports suspension is the same spring rate as the 350z.

Regards.

Edited by o2bfit

thanks for the replies guys.

for anyone else following this thread here is the pictures of the sedan with 350z suspension.

http://www.skylinesaustralia.com/forums/topic/282805-review-stock-350z-suspension-vs-stock-v35-suspension/

apparently a 1" drop. Doesn't look it in the images though.

I don't really want secondhand shocks, so the GT-8 stuff is out, unless I buy new from Nissan.....if I wont the lottery.

Im still trying to find out if the tokico G35 shocks will fit, I suspect they will, but Im concerned they are for the coupe and not the sedan and I dont want the drop.

thanks for the replies guys.

for anyone else following this thread here is the pictures of the sedan with 350z suspension.

http://www.skylinesa...v35-suspension/

apparently a 1" drop. Doesn't look it in the images though.

I don't really want secondhand shocks, so the GT-8 stuff is out, unless I buy new from Nissan.....if I wont the lottery.

Im still trying to find out if the tokico G35 shocks will fit, I suspect they will, but Im concerned they are for the coupe and not the sedan and I dont want the drop.

I looked at importing some shocks from www.shox.com. Here is their US pricing. They mentioned the part numbers were different for the G35 and V35. I don't believe they are.

TOKICO - Shocks HP $279.00

Tokico DSP adjustables $589.00

Sets of 4 F&R

DHL shipping $149.00

The Infiniti G35 started in 2003 in the U.S.

Koni lists different part numbers for the 2001 Skyline and the 2003-2007 G35 Are you sure they will fit?

Regards

The Tociko blue shocks should fit our sedans...the skyline v35 sedan and the infiniti g35 sedan are the essentially the same car.... parts are interchangeable. I've got RSR down springs in my sedan and I'm hopefully going to change my shocks to Tokico once my stock shocks go. The Tokico blue shocks are pretty much OEM spec

Edited by Alphamox
  • 1 month later...

I havent got much further with this as I need to measure the shocks and I cant really afford to have this car off the road too long.

So Ive decided to go with the 350z suspension option.

Can anyone confirm that all I need is 4 shocks and 4 coils ?

are any of the bushes or brackets different ?

Make sure you get '05 350z springs, with earlier the arse end will sag a bit more.

Cheers

I see that the 04.5-06 coils have a higher spring rate than the earlier ones.

http://www.350z-tech.com/zwiki/Part:Springs

interesting.

thanks for referencing my post...

if u go for 350z suspension on a sedan, you will get some camber on the rear. However, it's not very bad and shouldn't give u camber wear on the tyres. It does make cornering a bit more stable.

I do suggest, that when u drop it, to go a bit wider on the rims. I would go no more than 8.5"...it will improve the handling of the sedan dramatically around corners...

Of course, my advice is just that - do your own research.

But then again, the GT8 standard suspension gives a really good and refined ride. I noticed what I was missing out on when I reinstalled my GT8 suspension when I sold the car. I'd probably wouldn't got for 350z suspension in hindsight...but then again, I don't own a V35 anymore...

thanks for referencing my post...

if u go for 350z suspension on a sedan, you will get some camber on the rear. However, it's not very bad and shouldn't give u camber wear on the tyres. It does make cornering a bit more stable.

I do suggest, that when u drop it, to go a bit wider on the rims. I would go no more than 8.5"...it will improve the handling of the sedan dramatically around corners...

Of course, my advice is just that - do your own research.

But then again, the GT8 standard suspension gives a really good and refined ride. I noticed what I was missing out on when I reinstalled my GT8 suspension when I sold the car. I'd probably wouldn't got for 350z suspension in hindsight...but then again, I don't own a V35 anymore...

What was it you didnt like about the 350z suspension ? by refined do you mean it was too hard ?

My wife and I both prefer hard suspension, probably because we both corner too hard :)

I agree the gt8 suspension is nice its just way to high. Eibach pro kit springs for the g35 are said to be the best compromise when lowering these cars.

I have 350z track spec dampers and cobra springs it handles unbelievably well but is firm. I have the track spec springs aswell but i think they are just to firm for a decent ride.

What was it you didnt like about the 350z suspension ? by refined do you mean it was too hard ?

My wife and I both prefer hard suspension, probably because we both corner too hard :)

As the buyer of that suspension from siu_loong_bao and having it fitted and running in my Sedan for last 5 months or so

It is the best suspension I could have bought..

350Z on the sedan is great at cornering, being the hardest sports suspension to be fitted in a standard car.

The car does have the Highway bounce effect as i think this one is an unrevised one make sure you pick post 05 suspension.

siu_loong_bao: Thanks the parts were in great condition indeed!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...