Jump to content
SAU Community

Recommended Posts

I have an R34 GTR Cooler for Sale in Very Good condition. It has the sensor hole at the back to prove its from an R34 GTR.

$550

Great upgrade for GTST!

R34BGTRa.jpg

Pic is not of actual cooler but is very similar to the pick

Need to sell ASAP

Avaliable for pick up from Moorabbin immediately

email: [email protected]

or SMS 0413 942 864 business hours, call after hours

Link to comment
https://www.sau.com.au/forums/topic/35039-r34-gtr-cooler-for-quick-sale-vic/
Share on other sites

Hey buddy I orginally bought piping & cooler off someone else in this forum, however the piping and the cooler do not match up properly and at the time i had fitted the new turbo and it was booked in for a tune, so i had to have an intercooler on it. As this cooler & piping did not match up i was forced to buy a new HKS cooler kit from UPI on the spot so now i need to sell the cooler & piping that i bought.. but now sell them seperately as they do not match up.. the piping is sold so now just the R34 GTR cooler, this can be polished up also for around $30.

Power wise, R34 coolers are good for around 300rwkw..

From stock GTSt if you had say exhaust/filters/boost 10psi id say you would make around 165-170rwkw, with the cooler you would easily increase up to 180-190 and be able to run 12-13psi more safely

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...