Jump to content
SAU Community

Cheapest Place To Buy 12X1.25 Nuts - Need Long Skinny Ones (Allen Key Type)


Recommended Posts

Where is the cheapest place to buy 12x1.25 nuts - need long skinny ones (allen key type) as I want to put the starcorp 3 piece 17's I have on my 93 telstar tx5 v6 onto my R33.

Just bought the R33 yesterday so driving around on bald tyres has to be rectified asap because I dont want a yellow sticker. I work in Malaga and can swing past Balcatta easily at 8am in the morning. Not looking to spend alot, since I can just get $150 worth of used tyres on the stock rims put on.

Don't get the Allen key type. They crack and rust and are made of cheese.

Go to Richards tyrepower in Osborne park on scabs beach road and speak to Lachlan... They'll have what you need.. 50 a set last I checked that's with locknuts too

Got some from Ben at Barbagallo Tyres for $60... needed them asap =(

Richards Tyrepower wanted $70.

Thanks for your help guys. Will need some for the Telstar probably so I'll keep Taleb in mind.

Well went to put the front wheel on and it won't clear the caliper... I think they are a different offset. I am working from this info:

(Car is 93 TX5 Ghia V6 2.5)

"TX5 from 4/92....PCD is 5/114.3, offset is 35 and centre bore is 67"

another site: "TELSTAR 1988 - ON 5 X 114.3 my own measurements offset +45 to 50 center bore 70"

Would a 10mm spacer get me out of trouble (yes I understand it will get me into trouble too...)

I just bought these wheel nuts for $60 and now im not going to have a car to put them on. If a spacer will do the trick then I would rather do that then spend $160 on some used tyres... need rear tyres asap, especially with the weekend coming up.

Edited by Justlikemusic

Im sure I could just buy the spacers from a wheel shop... it's only 10mm. Rims have 215/45's on them so I might be able to get away with 15mm spacers if the TX5 Rims are a +45 offset. Im sure the standard wheel stud will be ok with a 10mm spacer, not too sure about 15mm though.

Was actually thinking of selling the car... auto gearbox is starting to give me the .........

I got told the front wheel drive offset is different to the rear wheel drive offset? Yet the cars are +40 and +45/50?? and 5x114.3

Tyre places said it doubles the stress put on the studs with spacers because the centre bore cant locate the rim?

post-49098-0-87191700-1295612420_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Great work! Thanks for documenting the process.
    • How would you even adjust the clutch if the pedal already has the correct free play? The operating cylinder has no adjustment in mounting position or rod length. On pull style clutches there is also no ability to adjust the bearing carrier. Push type I can see how adjusting the carrier height makes it all work.   If this is the twin plate clutch did you verify that your friction disks were oriented correctly? It's not mentioned in the directions at all you just have to notice that one side the friction disks have a part number on the hub fingers and a subtle coning to those fingers. Another thing that I noticed was if you put the friction disks in backwards the pressure plate fingers will not be even and flat when the clutch is installed.
    • yeah, mechanically, it is probably do-able, off the top of my head, there would be the transfer case, which I believe will bolt up to the rear of the RWD transmission, the shorter rear tail shaft. A front drive shaft, front diff, engine upper sump, front drive shafts, front hubs and front AWD struts (they are shaped around the front drive shafts), LCAs (at the very least from the front suspension) oil cooler.  You might want the rear diff from an AWD too, so you can be certain the front and rear diff rations are identical.  Who knows what brackets and mounts you might need.  So a whole doner car might be the best option if you need to maintain RHD. Then actually making it work, that would be a whole different story.
    • Take the fall as a warning sign for future endeavours  Stay safe mate
×
×
  • Create New...