Jump to content
SAU Community

How To Lower V35 Sedan ?

Hadou Ken
 Share

Recommended Posts

Deep Dish V35 Experienced

Deep Dish V35

Posted
Posted (edited)

the 350z shocks and springs in my 250gt sedan exactly replicates the "driving on bumpstops" sensation, this is in comparison to a previous car i owned which infact was on the bumpstops.

it is also important to note that i roll on 235-35-19's..... so there is no sidewall to absorb bumps either

it is shaking the crap out of my interior. have noticed a few new constant squeaks and rattles including centre console, left a-pillar and parcel shelf from the first drive with Zs fitted. most of the bouncing is now just me being thrown out of the drivers seat, and items in my boot getting airborne. and im no hoon, i only drive at 55. it is quite simply horrible

Edited by Trick V35
GeNOS Collaborator

GeNOS

Posted
Posted

i really want to know if people have had personal experience rather than word of mouth.....

plenty of people say bmws are too expensive to own and fix, but i proved they were cheaper than holdens with a bit of know how

its not word of mouth.. its personal experience i read from the guys on g35driver forum

austingtir Contributor

austingtir

Posted
Posted

Might find you scored the track spec 350z suspension? It is firmer than the standard 350z stuff. Either that or get rid of the 350z springs and buy some eibachs they are the best springs for the money around imo.

Im running 350z track shocks with aftermarket springs and the ride is o.k its firm but not ridiculous.

n15m0 Grand Master

n15m0

Posted
Posted

the 350z shocks and springs in my 250gt sedan exactly replicates the "driving on bumpstops" sensation, this is in comparison to a previous car i owned which infact was on the bumpstops.

it is also important to note that i roll on 235-35-19's..... so there is no sidewall to absorb bumps either

it is shaking the crap out of my interior. have noticed a few new constant squeaks and rattles including centre console, left a-pillar and parcel shelf from the first drive with Zs fitted. most of the bouncing is now just me being thrown out of the drivers seat, and items in my boot getting airborne. and im no hoon, i only drive at 55. it is quite simply horrible

What you are describing shouldn't be the case...I'm riding on 235/40/19. Either your shocks are dead or as explained above you got the track version.

Deep Dish V35 Experienced

Deep Dish V35

Posted
Posted (edited)

Might find you scored the track spec 350z suspension? It is firmer than the standard 350z stuff.

Im running 350z track shocks with aftermarket springs and the ride is o.k its firm but not ridiculous.

aaaaaah! theres something ive overlooked! time to do some part number research. if thats the case, i'll be looking for non-track items. they definitely feel as though they would be more at home on a smooth racetrack than roads with manhole covers and speedhumps.

Edited by Trick V35
Deep Dish V35 Experienced

Deep Dish V35

Posted
Posted

aaaaaah! theres something ive overlooked! time to do some part number research. if thats the case, i'll be looking for non-track items. they definitely feel as though they would be more at home on a smooth racetrack than roads with manhole covers and speedhumps.

Research suggests I have the early 350Z setup with the stiffer rate rear springs. The later 350Z's have same fronts but softer rears, which would be better IMO.

  • 1 month later...
  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Radiator removal

      By Duncan · Posted

      So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...