Jump to content
SAU Community

Power FC Tunners

Gdup

By Gdup,
in General Automotive Discussion

 Share

Recommended Posts

GZ R33 Community Regular

GZ R33

Posted
Posted
Does any1 know of C and V performance? Are they good at tunning, especially tunning the FC?

Does anyone recommend? If not, who else do you reccommend? Also i am in sydney.

Cheer All

Apparently Croydon are the only ones in Australia that have the software, all others tune off hand controller. (With software there is at least 30kw more)

Link to comment
https://www.sau.com.au/forums/topic/35160-power-fc-tunners/#findComment-702523
Share on other sites
Gdup Apprentice

Gdup

Posted
  • Author
Posted

But wouldnt using the hand commander be better? because you are using the FC's own tunning product? Im using CRD developed thier own program because they were tunning the FC's before the hand commander came out.

Apparently Croydon are the only ones in Australia that have the software, all others tune off hand controller. (With software there is at least 30kw more)

If this is true, then wouldnt everyone go to CRD?

Link to comment
https://www.sau.com.au/forums/topic/35160-power-fc-tunners/#findComment-702988
Share on other sites
Jimbo2000 Grand Master

Jimbo2000

Posted
Posted
But wouldnt using the hand commander be better? because you are using the FC's own tunning product? Im using CRD developed thier own program because they were tunning the FC's before the hand commander came out.

 

If this is true, then wouldnt everyone go to CRD?

as far as i know the PFC HC has been available with the FC since it was invented.

the laptop software allows them to tune in 300 units instead of the 60 units that the HC allows (not the right figures but you get the point)

i would also guess that the laptop software will not guarentee any extra power just easier tunability thus more can be done a lot easier and quicker.

Link to comment
https://www.sau.com.au/forums/topic/35160-power-fc-tunners/#findComment-703242
Share on other sites
B-Man Grand Master

B-Man

Posted
Posted

Bullshit about the laptop software for PFC - A good tuner can get the same result but it will take longer. The HC is awkward and lots of writing on paper. But if they know what they are doing , not having the Datalogic whateva is not entirely neccessary.

My 0.2c

Link to comment
https://www.sau.com.au/forums/topic/35160-power-fc-tunners/#findComment-703269
Share on other sites
Jimbo2000 Grand Master

Jimbo2000

Posted
Posted
Bullshit about the laptop software for PFC - A good tuner can get the same result but it will take longer. The HC is awkward and lots of writing on paper. But if they know what they are doing , not having the Datalogic whateva is not entirely neccessary.

 

My 0.2c

Correct

Link to comment
https://www.sau.com.au/forums/topic/35160-power-fc-tunners/#findComment-703598
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      (it is a brand new ported mellings pump) I suspect the lack of pressure is due to the leak. It was *not* that low in other logs of oil pressure in the past. It wasn't that hot either, but not far off.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Would a Mellings oil pump be a viable option  From my time with a LS, and talking to tuners and LS specialists, the "weak" OEM oil pump is one of the first things they recommend to swap out if I was going to give the engine any high RPM I opted for a Mellings high volume, with the high pressure springs and I never had a issue with it Cost wise they are not expensive in the scheme of things 
    • davemoto63
      My new to me M35 Stagea wagon

      By davemoto63 · Posted

    • davemoto63
      My new to me M35 Stagea wagon

      By davemoto63 · Posted

      Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
×
×
  • Create New...