Jump to content
SAU Community

Recommended Posts

I just picked up a GT Coupe NON turbo for $5500, I know a bargain, well it was my cousin who sold it to me. The engine is in "pretty good" condition, it's not exactly immaculate. it runs but there are several oil leaks and it needs a ring change as per the mechanics saying. I'm thinking about putting an RB26 in. What would it take? I know I have to guy the engine but after that, do I have to do modifications to the chassis or just bolt in. How do I hook it up to the drive shaft. I know I'm a noob but if I'm doing a swap then why not the RB. By the way what about the RTA, do I have to notify them or something. Is this even legal to do. Do I have to get the car reinspected by blue slip. What about cops won't they ask why it's a RB26 not the stock engine, even if I tell the RTA? Please guys the engine in this thing is ****ed up, it runs but my mechanic said change it, the cracks in the sump are too expensive and not worth it.

Link to comment
https://www.sau.com.au/forums/topic/351707-r34-gt-coupe-build/
Share on other sites

Prepare yourself for alot of money and a fair bit of headfarking.

RB26 in good condition: $4,000 - $4,500.

Custom sump (without diff): $500

Installation labor: $1,000 - $1,200

Then prepare yourself for blown turbo town, most rb26's turbos are getting on, and it'd be a wise move for the sake fo your engine to swap to a single or get new -5s (GT2860) within the next 6 months.

You'll have to notify the RTA, I don't know about eastern states laws, but you'll def need an inspection of some sort. You wouldn't wanna risk it, You'd barely last a few weeks judging by the rate that skylines get hassled on the roads, and they'd take one peek in your engine bay and see that it's not stock...

+ electronics, ecu etc??? i needed all those parts when i did my conversion. also exhaust would needa be redone, dont know if you still need to modify your brakes either if you put a higher performance engine into your car, the non turbo brakes are so small you can barely stop a horse with them.....

engineers report or certificate???

also are you still allowed to put an older motor in a newer car??? somewhere i read about that, or was that just for compliance??

a copper aint going to look your vehicle record and see that it is a non-turbo, or and RB26 bla bla bla.

They will seach your plates and see "Nissan Skyline", nothing else. A police officer is not going to be able to tell that your car is a factory non-turbo just by looking at the vehicle record, nor will they be able to tell the difference between and RB26 and an RB25 non-turbo, expect for the few police officer's who may have some mechanical knowledge....

don't forget a turbo gearbox (unless the r34 natro boxes are stronger than the r33 natro boxes), brake upgrade (if needed), LSD.

yes you need to notify the transport department. you may possibly need it blue plated.

to be honest, for what it will cost you to do it you could sell the natro, buy a turbo 34 and do mods to it and be making more power than a stock 26.

That's not the point, a built Civic might too but I loath civics lol. The point is the RB26 has more potential and is bigger. I mean why bother with an RB25. The 26 STOCK is BETTER. It's just the way it is. Now I could build a RWD GT-R here, yeh its not going to be a GTR but I never said it was. It's an RB26 Skyline RWD. I'll even put the GTR body kit and fenders to give it that look.

Anyways so what should I do at first, ask the RTA or build the car then go. Is it the RTA or the transport department or are they the same which you're talking about. By the way when cops look they don't see a Skyline GTR they see skyline so he's going to harass me, naturally as he is a useless loser. But anyways be that as it may I don't want trouble. So what should I do first for those who have done. What did you guys do?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...