Jump to content
SAU Community

Recommended Posts

You have a sensor thats usually located in the air ducts so the a/c doesn't freeze itself. Their is also a pressure switch out front near the radiator (looks like a cylinder with two wires going to it) But I havent pulled my line apart yet to find out. This is where a service manual would come in handy.

the sensor is displaying on the climate control (self diagnostic) that it is 5 degrees.. thus when i turn a/c on.... it turns itself off... cause it thinks it is 5 degrees.. obviously 2 cold for the a/c....

Sumo u mentioned it could be in the air ducts..... could this be possible?

Anyone else know the exact location of this sensor?

wados: it wouldn't be the sun sensor, that just gives a bit of an "adjuster" to the basic climate algorithm, based on the outside light levels

Refrigerant sensor will be down under the whole dash near the aircon box. There are a few sensors down there in the ductwork from what I remember (and if its similar setup to an R33). You will have to remove it to get to it (few hour job). Replacing the sensor itself should be an easy job, just unplug old, and in with new. Its just getting to it.

ahhh..here we go.. I think this looks like it.. Its going into the aircon box there so I assume that is what its doing!

Now that I think about it, it could also be that temp resistor that goes from the climate control to just behind your front dash. I know on the 33 at least, its attached to a small hose, that goes to a very small vent just near the steering wheel and below left of the speedo, etc. Not sure about the R32 though, I assume it would have a similar setup.

hey guess what everybody - I hope you've all realised TODAY IS A LEAP DAY!!

so enjoy this one day every 4 years occasion! and party likes it 2000 all over again! and couldn't be a better day for it up here either :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...