Jump to content
SAU Community

Recommended Posts

Hi Guys,

I've recently sold my skyline R33 GTST and am parting with the bits and pieces left over:

* Standard r33 GTST wheels in excellent condition, rubber on 3 of them is in good condition, 1 tyre will need replacing $170 ONO

* S2 Air Flow meter excellent condition $30

* S2 ECU (Excellent Condition) $30

* Dump pipe with heat shield (Excellent Condition) $10

* Standard injectors (x6) (Excellent Condition) $40

* Standard cam shaft and cam gears (Excellent Condition) $30

* Standard Fuel pump excellent condition $30

* Standard air filter box with cold air intake, air filter and intake pipe (Excellent Condition) $40

* R33 S1 Front Grill (Excellent Condition) $40

* R33 Side Mount Intercooler great condition $40

* R33 Standard rear Springs (Excellent Condition) $40

* Standard Valve springs $10 (x24)

* 2 x 10" kenwood subwoofers and 2x Kenwood 6" speakers $50 (Great condition)

* 2 x 10" Ramage Subwoofers (Brand new boxed never used) $50

* 2 x 10" Venom subwoofers with boss amp (Excellent working condition) $50

Pick up is available from Canberra or I can post the smaller parts to your location.

Ta.

post-48356-0-09794800-1296108130_thumb.jpg

post-48356-0-15713500-1296108153_thumb.jpg

post-48356-0-17350600-1296108175_thumb.jpg

post-48356-0-93723100-1296108200_thumb.jpg

post-48356-0-13905700-1296108224_thumb.jpg

post-48356-0-10277800-1296108299_thumb.jpg

post-48356-0-85318700-1296108327_thumb.jpg

post-48356-0-41860800-1296108351_thumb.jpg

post-48356-0-77533500-1296108380_thumb.jpg

post-48356-0-76893800-1296108419_thumb.jpg

post-48356-0-16840900-1296108443_thumb.jpg

post-48356-0-82753600-1296108464_thumb.jpg

post-48356-0-08832300-1296108491_thumb.jpg

post-48356-0-17241700-1296108550_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/351874-fs-r33-gtst-standard-parts/
Share on other sites

  • 2 weeks later...

How much to deliver the R33 Side Mount Intercooler great condition $40 to NSW 2756

Also interested in the wheels just need to organise a trip down from sydney

Phill

Edited by Phillhunt

Hi, are you able to post the air box, cold air intake etc to Adelaide? If so how much? Very keen on this!

Cheers

Hi

Yes, should be able to post it for around $20 - $25 depending on location in adelaide.

Ta

ey mate could u gimmie a contact number so i can arrange payments n postage plz or if u could can u sms me on 0432 506 443

What were you after?

So far I've sold the following:

*Wheels

*Airbox

*Injectors

*S2 ECU

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep it sure does.   Tone wheel lines up in the same spot perfectly.    
    • Something I meant to say when we were chatting the other night about having an open trailer floor being great to work on a car, but you've never used the feature... It's a great place to park a car after doing suspension component changes, and do the tightening of all the bushes with the car sitting at full ride height. Especially when you don't have a 4 post hoist!
    • That is way more science than even I would use. I just eyeball it, not even accounting for the non-verticality of the tape measure when held on the lip and the centre at the same time. +/- 2mm is good enough for the girls I go out with.
    • So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
    • So....knowing that I have a problem with power steering temps on track and another Wakefield day booked in next Friday, I've done the obvious thing They are very reasonably priced at $1650, considering they are a big monotube shock, double height adjustable (don't have to change pre-load to change ride height), one way adjustable damping and standard sized and customisable springs if you want something other than what comes with them. They come with 9kg/mm front and 4.5kg/mm front and I went with that as a starting point because I'll add adjustable sway bars too https://justjap.com/products/bc-racing-coilover-kit-ds-ds-infiniti-q50-v37-14-current#description Unfortunately they didn't come with rear strut tops so I've re-used the factory ones which was a bit of a pain. Also, the adjuster for the rear shock will be an absolute nightmare to get at, and while there are extensions in the kit I can't see any way you can actually attach or use them
×
×
  • Create New...