Jump to content
SAU Community

Recommended Posts

This topic has been covered many times before.

My opinion - go for a high flow panel filter like a K&N. Though you'll only be looking at minimal power gains. To maximise bang for buck, you could run another pipe from the front bumper up to the airbox for extra cold air (together with the stock airbox intake funnel).

I think pod filters are a waste of time with or without a heat shield.

Cheers

I used the search button and found this thread! I also am thinking of removing air pods and goin for stock airbox. But dunno if my GReddy intake piping will line up with a stock air box.

Maybe a custom made one is the go! ? Can't imagine all that hot air is doin the intercooler any favors....

I agree,

I think after reading many threads & different methods the best set up is a dry panel filter with a custom cold air intake

system at the front bar...

This thread was purely intended to get as many people's outlooks on Pods Vs Panel set ups, so please throw in your 2c.

  • 3 weeks later...

If you go pod you have to build a heat shield, otherwise it will only sap power and promote detonation. They do make it sound better apparently though. The verdict, thread after thread, tends to be go with a decent panel filter, and cold air intake if you're hardcore :D

  • 1 month later...
  • 1 month later...

When i bought my 33 gtst it came with an uncovered pod. I was made aware of them soaking up heat so i made a shitty shield in an attempt to stop it, but dont think it helped much. I have never really cared either way, but after going in my other mates gtst with standard air box, the pod does give my car a much cooler induction sound. I honestly dont think there is too much in it if both are set up well, but there is a sound difference.

Thread closed. Believe it or not, but since SAU started more than 7 years ago, this topic has been discussed before.

Please use the search function in future. It may be found here:

http://www.skylinesaustralia.com/forums/search.html

While we understand that it can be frustrating to have your thread closed - Please consider that other members may feel it to be disrespectful and selfish of you to post a simple question, without using the search feature to review the wealth of information provided by said members over the years.

If you still feel that this action is unjust, then please PM r31nismoid or pal and we can discuss it further.

Edited by Thelen

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...