Jump to content
SAU Community

Recommended Posts

Hey guys,

My stagea is 4WD turned RWD, Previous owner had the front driveshaft removed I believe.

I'm thinking about fitting wheels which are:

18*8.5 +22 on the front and 18*9.5 +35 on rears. 225/35 on fronts and 245/40 on rears

Will this be fine to run considering I'm RWD?

Thank you.

Edited by gersfan
Link to comment
https://www.sau.com.au/forums/topic/353381-stagea-staggered-fitment/
Share on other sites

Hi Rohan,

mate as long as rolling dia are same,should be sweet,

& as you may have read no need to pull front shaft,

Bubba is running RWD at moment with shaft in,

Good luck with small sidewall on WA`S poor roads,

how is he doing this? there is NO way you can safely run in rwd without pulling the shaft!

Bullshit. I've been running mostly in RWD since a couple of weeks before Powercruise. I have posted this up time and time again, if you refuse to believe, that's your problem but don't scaremonger.

Rohan, you want to run something like 225/40 and 245/35 to try keep the rolling diameter the same.. if you know what tyres you will be using, do a bit of research and match up some front and rears.

e.g. I run Federal 595's, if I was going to stagger I would go (depending on rim width) 255/35ZR18 90W 633mm OD and 225/40ZR18 88W 635mm OD

I think ATTESA can handle up to 5% difference before it flips out.

http://www.federaltyres.com.au/tyres/high-performance/595

18"

215/35ZR18 84W RF 606 7.0- 8.5 500

225/35ZR18 83W 613 7.5- 9.0 487

255/35ZR18 90W 633 8.5-10.0 600

265/35ZR18 93W 641 9.0-10.5 650

215/40ZR18 85W 629 7.0- 8.5 515

225/40ZR18 88W 635 7.5- 9.0 550

235/40ZR18 91W 643 8.0-9.5 615

245/40ZR18 93W 651 8.0- 9.5 650

225/45ZR18 91W 658 7.0- 8.5 615

245/45ZR18 96W 676 7.5-9.0 710

255/45ZR18 103Y XL 687 8.0- 9.5 875

235/50ZR18 101W XL 692 6.5- 8.5 825

255/55R18 109V XL 735 7.0- 9.0 1030

I ran staggered offsets with it still being 4wd. 8.5 +22 and 9.5 +25's. It was fine. Ijust ran 235/45s front and rear.

If your's is an auto, you will struggle to get a 9.5 +35 to fit. I run +22 and without camber arms it touched the coilover body on big bumps.

I ran staggered offsets with it still being 4wd. 8.5 +22 and 9.5 +25's. It was fine. Ijust ran 235/45s front and rear.

If your's is an auto, you will struggle to get a 9.5 +35 to fit. I run +22 and without camber arms it touched the coilover body on big bumps.

Manual, I'm probably just going to get them and if I have problems I'll change the tires so that diameter is the same.

Thank you everyone.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...