Jump to content
SAU Community

Recommended Posts

phew ..... lucky outcome actually. Surprised valves didnt smash themselves to pieces.

glad you got out of it in the end.

Question : how many kms has the car done? was the stuffed belt in bad/worn condition or was it the bearings fault?

AFAIK the prob was a seized bearing in the idler pulley. From what I saw, the inlet side has hopped six teeth, the exhaust side only one tooth. A new belt was fitted and the car started OK and was driven out to be fixed tomorrow when the new kit arrives. It is all very perplexing caus all the other threads I have read on this subject have reported severe internal bleeding. It must be remembered that the T/B did not break. It was partially laminated. I can only surmise that the ecu detected an abnormality in the "what?", and went into limp before any serious damage occurred.

Thank you Mr. Nissan.

I am off to the Newsagent tomorrow to get that winning ticket. Thanks Duncan. :thanks:

phew ..... lucky outcome actually. Surprised valves didnt smash themselves to pieces.

glad you got out of it in the end.

Question : how many kms has the car done? was the stuffed belt in bad/worn condition or was it the bearings fault?

[/quote

The belt had been replaced at 105ks. Was a Gates. The belt was OK on the tooth side. The outside was laminated due to the seized bearing in the idler pulley.

Moral: When replacing the belt, replace the pulleys.

ahh there you go :D moving a few teeth is totally different to snapping entirely where the crank and valves can move independantly.

SR cams or not, surely the de motors have higher compression and therefore pistons protrude further into the valve area?

And yes.....always replace the idler and tensioner! This is far from the only motor this has happened to over the years :( Also, importantly, replace the stud that the tensioner attaches to, and the bolt that the idler uses, they can also break, particularly if poorly tensioned at some time in their history

phew ..... lucky outcome actually. Surprised valves didnt smash themselves to pieces.

glad you got out of it in the end.

Question : how many kms has the car done? was the stuffed belt in bad/worn condition or was it the bearings fault?

its always advised to do the tentioners when u do ur timing belt so what happend dosent most people are to cheep but it certainly pays off

having bearings, belts etc being replaced on the rb26 atm - track duties 3x per year only but no point playing Russian roulette

then again, also replacing rod bearings at same time, crankshaft being machined, oil return system, etc :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...