Jump to content
SAU Community

Tyre Issue (Pic)

druzilla32

By druzilla32,
in R35 GTR

 Share

Recommended Posts

druzilla32 Mentor

druzilla32

Posted
Posted

Had this happen to me on tuesday

181904_1283235217183_1719195671_507243_6217350_n.jpg

Any thoughts?

I have been running 4 deg camber for last 5 track days, last 5 track days I have been using 2nd hand pcup slicks.

On tuesday I used new slicks and this happened at the end of 3rd session, (about 15 mins on track)

Tyre pressue was 37 after 1st session.. I then dropped to 28... So would have been a bit over 30 when this happened.

There were no lockups and the wheel didnt hit any curbs.

Thanks for any help.

Link to comment
https://www.sau.com.au/forums/topic/354254-tyre-issue-pic/
Share on other sites
handbrake Veteran

handbrake

Posted
Posted

Drew, some reckon that with the weight of our car we should be more towards 35 psi, I normally run around 35 psi but experiemented with 31 hot on tuesday. My tyres look fine and wear is good and even, with a fine ripple over the entire surface. did you check any temps on the day?

do you have any suspenison components rubbing?

damage during mounting i suppose is the only other thing I can think of.

either way mate, sorry to see your day ended like this, you were putting out some impressive times.

Link to comment
https://www.sau.com.au/forums/topic/354254-tyre-issue-pic/#findComment-5674791
Share on other sites
handbrake Veteran

handbrake

Posted
Posted

I recall the WRS guy at the track said it didnt think it was a puncture (at least not from trauma to the tread) but I guess with the way it is chewed up how could he tell. have you had time to give it a good going over Drew?

Link to comment
https://www.sau.com.au/forums/topic/354254-tyre-issue-pic/#findComment-5674997
Share on other sites
druzilla32 Mentor

druzilla32

Posted
  • Author
Posted

Drew, some reckon that with the weight of our car we should be more towards 35 psi, I normally run around 35 psi but experiemented with 31 hot on tuesday. My tyres look fine and wear is good and even, with a fine ripple over the entire surface. did you check any temps on the day?

do you have any suspenison components rubbing?

damage during mounting i suppose is the only other thing I can think of.

either way mate, sorry to see your day ended like this, you were putting out some impressive times.

Nah, didnt check tyre temps on the day.. I will be sure to do this in the future though.

No components were rubbing on the tyre from what I could see.

The guys from WRS have the tyre now and will give it a good look over

Yeah its a shame this happened, but then I dont think I would have got much more track time in with the rain soon after.

How did you end up going with times? get back out there later in the arvo?

Link to comment
https://www.sau.com.au/forums/topic/354254-tyre-issue-pic/#findComment-5675048
Share on other sites
handbrake Veteran

handbrake

Posted
Posted

no, left before lunch. no better times later in the day. was pretty happy with the time we got considering the car was a handful (oversteer) after we changed the roll bar settings. a few tweaks hopefully will sort that out for next time out.

Link to comment
https://www.sau.com.au/forums/topic/354254-tyre-issue-pic/#findComment-5675065
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...