Jump to content
SAU Community

Recommended Posts

Have a look in this thread, especially at Jay51's PVC pipe mod down near the bottom. Combine that with an airbox/partition and even the factory scoop and you'll be getting plenty of air in there.

I found that my car ran significantly harder with the pod filter installed over the stocker airbox, dispite sucking in underbonnet air. The only things I've done to mine are a 3" turbo-back exhaust, pod filter and 12psi.

Swapping back to the standard airbox and resetting the ECU made the car feel flat and lifeless, putting the pod back on and resetting the ECU again brought it back to how it was.

Hey _turtle_,

I went to make a start on the airbox like I said, when I realised that there was a MUCH easier way!

I thought about what surreal said about taking the front off which gave me an Idea! I cut the front of my airbox off (like surreal did I assume), and I blocked off any engine heat from getting to the hole with perspex.

Next I will put some foam/sponge on top of the airbox, and the perspex mould I made to completely block it off, and there you go. More cold air in 3 easy steps!

I have attached an even crappier pic than last times... :D

Actually there is no perspex divider at the back of the box, just the front!

I used cardboard to get the shape right around the intercooler pipes, and the radiator support.

Then I cut a larger piece on perspex than was needed, so I could use the heat gun to mould it into a shape that would fit nicely into place.

It actually looks a bit retarded at the moment, but once I put the finishing touches it will look much neater.

damn, that 2nd picture is heaps better zahos! even had colour! now i know whats happening. now i know wotcha mean about the front of the box, just the lid part, i thought u meant the whole front. so have u actually done all this yet? notice any difference?

I've cut the front out, and I've made the barrier and put it in place. It is now almost as noisy as a pod filter!

As for performance I did notice that the car feels less restrictive at high revs, my boost was upped by .2 bar, and boost hardly spikes now!

I had to wind the boost back down, b/c at .9 bar it was running like sh1t b/w 5 - 6K rpm. Once I make the barrier more secure, and I put the foam on top to block warm engine air coming through, I'll be finished and I'll try to take a pic with someones digital camera 4 u to see!

Where abouts in melbourne r u?

  • 2 years later...

Hey guys, i wanan cut a hole on my stock box and have a pipe so more cold air gets into it, now i know there is a fair few threads on this sorta topic, but none of the links for pics work. so i was wondering if anyone has any links or pics of some sort of piping on a stock R33 air box? cheers.

What I am doing on the Stagea (same as R33) is building a scoop into the alloy radiator guide I am fabricating. The concept is that, as air comes in through the grill, it gets scooped up and pointed at the standard airbox inlet. Too hard to describe much more than that in words. When I have it finished, I will post some pictures on the Stagea forum.

I can't see any pics of the mods ?!!

also,, umm, u know how under the airbox (inside) lid is a black foam thingy,,

is it a good idea to remove this?? is it there to reduce turbulence or absorb moisture?

does anyone what i'm talking about,,?? if not i can post up some pics,, later on,,,

or if possible can someone email me the pics of the airbox mods

[email protected]

thanks

Afro

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...