Jump to content
SAU Community

Recommended Posts

Hey fellas time to move on the old girl so I can make inroads towards my new project.

1982 DR30 FJ20ET Coupe complianced in QLD in 2007.

Has new shocks and springs and some urethane bushes. Gearbox feels tight and smooth. Told by previous owner it has a blown head gasket and turbo has a blown seal. Complete Stewart Wilkins gasket set included. 120 odd thousand km on dash off the top of my head.

I've installed a neat Nardi wheel to replace the standard foam POS.

Seats need replacing, rest of interior is in gc (red & black).

Paint is shagged, There is one small spot of rust on the rear apron, only other spot is in the right sill panel (pictured)

Tail lights are faded but have no cracks.

Extremely rare rear under spoiler or 'slit spoiler' fitted. You will not find one fs in japan let alone here.

NOS RS badges on front quarters.

IMG_3640.jpg

IMG_3653.jpg

IMG_3672.jpg

IMG_3673.jpg

IMG_3646.jpg

IMG_3671.jpg

IMG_3656.jpg

$2200 Firm

Please reply here or via PM

Location: Sunshine Coast QLD

Edited by D-limo
Link to comment
https://www.sau.com.au/forums/topic/358333-fs-s1-dr30-coupe/
Share on other sites

non-goer door to door through toll was $2100. thats toll though so im sure can get it cheaper..

It cost me $850.00 by Door to Door Car Transport from Sunshine Coast to Castle Hill & they quoted the other figures when I enquired recently. CEVA are about $1600 to Adelaide and these 2 are about the cheapest.

D

  • 1 month later...

Thanks man, got Pretty much what I was asking for. Buyer owns a performance garage and is using it as a base for a gibson motorsport replica race car.

So Goatrider you can shove your 1500 dollar 'wreck' offer up your ass :)

Edited by D-limo
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...