Jump to content
SAU Community

Recommended Posts

Possibly had a mind change from my RB26/30 idea, gauging interest on selling the lot or bits to sort different engine option:

R32 RB26DETT with everything bar coil packs and alternator. Spun a bearing, crank would want to be replaced.

Everything is disassembled bar the head itself, which looks to be in good condition.

If someone wants the Head, I will post up all the other bits separately, or they can take the whole lot.

Head:

Standard, complete with cams.

$1200 FIRM.

The Lot:

Block, Sump, Pistons/Rods, Crank (useless), Head, All Covers, Near New Clutch, Flywheel, Injectors, Inlet Plenum with T/B's, Exhaust Manifolds, Dumps, Turbo's, AFM's, Intake Piping, Oil/Water Lines, Wiring Harness, Mines ECU (car was making 230kw), Starter, P/S Pump, Ignitor, CAS, pretty much everything really. Get a new crank, bearings and complete RB26 Gasket Kit - you're away. Basically, I have a couple of boxes just in the parts for it.

$best offer.

Also have an RB30e Auto complete with Loom and ECU if anyone is interested, but I paid top dollar for that to see and hear it running prior to removal - so not giving it away.

PM or call me on 04 18 579 423

Located in Howrah - Scott.

Link to comment
https://www.sau.com.au/forums/topic/358448-eoi-r32-rb26-headtop-endcomplete/
Share on other sites

  • 3 weeks later...

let's re-invent this one.

Head Complete, minus covers, coilpacks, harness, manifolds etc.

$1200.

Complete Top End (All In Bits) including harness and ECU (Mines)

$2200.

Good Condition RB30e + Auto Complete (only selling once head sold)

$450.

Whole lot:

$2500.

2 complete std engines minus turbo , both have the heads off as i was getting them cleaned up for rb30 conversion :) , 1 rb25 loom , 1 rb25 to cefiro/laurel loom , gearbox, cefiro/laurel rb25 tailshaft . Theres other bits and pieces , i have a r33 wreck laying about :ph34r:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...