Jump to content
SAU Community

Lowest Legal Ride Height

AAARGH 33

By AAARGH 33,
in Western Australia

 Share

Recommended Posts

AAARGH 33 Community Regular

AAARGH 33

Posted
Posted

Hey guys,

Im just wondering what the lowest legal ride height is because my car is unregistered atm and I was worried about it passing pits.

When I bought the car the previous owner had already installed Öhlins suspension on it and it doesn't look height adjustable to make it any higher.If it is too low how can I raise the suspension instead of dishing out $$$ on coilovers?

Ive heard it is 100mm from the lowest part of your exhaust,can anyone confirm that? Mine is currently sitting at 70mm from the lowest part of exhaust.

Link to comment
https://www.sau.com.au/forums/topic/359134-lowest-legal-ride-height/
Share on other sites
AAARGH 33 Community Regular

AAARGH 33

Posted
  • Author
Posted

Borrow some wheels from someone which have huge tyre profile lol.

Yeah,slam some 4x4 wheels on there,she'll be right haha

yeah 100mm to the lowest point when all seats are loaded with passengers.

suggest you find some stock struts and springs to put in!

I think that might be the way to go.Anyone got some spare stock struts and springs lying around? lol

AAARGH 33 Community Regular

AAARGH 33

Posted
  • Author
Posted

Also would i still be able to pass with a front mount and a fujitsubo 3inch catback or am i going to have to swap them for the stock ones too?

And ive got a blitz pod but hopefully a CAI would be able to cover that.

bubba Grand Master

bubba

Posted
Posted

As long as you didn't hack up the reo bar to fit the FMIC and it's supported well you should be fine. 3in catback should be ok too, unless it's stupidly loud...

Yep, make sure you have the pod filter bracketed down at two points as well.

Ten Four Grand Master

Ten Four

Posted
Posted (edited)

LOL, I got so lucky with mine haha.

IMO, just do your best, make it look respectable (legal/clean as you can), go down with a good attitude (dress properly.. no thongs, singlets/cap backwards etc) talk to the guy, just bought it fixing it up for rego, stupid previous owner did that, so I fixed it it this etc etc.

If you still fail, you get a list of what NEEDS to be changed to pass, then you got 30? days to fix that list and you're sweet.

Edited by Ten Four
VNS 24 Mentor

VNS 24

Posted
Posted (edited)

You heard correct, lowest part of car must be 100mm.

Pump lots of air into tyres....

Which part of the car is exactly the lowest part of the car? Is that the exhaust part?

I asked because my front lip is sitting at approximately 80mm off the flat ground level. :P

Edited by VNS 24
AAARGH 33 Community Regular

AAARGH 33

Posted
  • Author
Posted

the mesh or the intercooler,or both?

Ive thought about this idea about painting the cooler black too but if it is good enough to pass pits doesn't that mean it should be alright with the cops?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...