Jump to content
SAU Community

Rb26 Conversion

fabr34

By fabr34,
in Engines & Forced Induction

 Share

Recommended Posts

fabr34 Contributor

fabr34

Posted
Posted

hi there i recently did a rb26 engine conversion on my r34gtt with a r32 gtr moter and a apexi power fc d jetro

wen it got back from adelaide the car was flat and the airbag light wont stop flasing

is there any way to stop that as i thort that r32 gtr dident come out with airbags that i would not have them any more

Link to comment
https://www.sau.com.au/forums/topic/359321-rb26-conversion/
Share on other sites
pistol-pete Veteran

pistol-pete

Posted
Posted

theres a reset procedure:

1. Turn the key from off to on.

2. Watch the airbag light closely. It will stay on for a few secs. and then as soon as it blinks off (the start of the flashing), turn the key off instantly.

3. Count to 5 (1 Mississippi, 2 Mississippi . . . .)

4. Repeat steps 1-3 two more times until you have done the cycle three times.

5. Now turn the key on and watch the light. It will start blinking in a different, slower manner. This is diagnostic mode. You can watch this for a little while, no hurry.

6. Now turn the key off again, Count to 5 like in step 3 again, and turn back on. If the procedure worked, the airbag light will not be flashing.

if that doesnt work theres another procedure for 33s that apparently works in 34s too.

Leave the drivers door open

Then turn ignition on so all dash lights are on but do not start engine.

When you have turned the key to that point press the drivers door interior light switch 7 times rapidly in succession,( within 7 seconds of turning ignition lights on)

Now the airbag light will flash at a different rate to before!

1 long flash followed by 2 short flashes ( the diagnostic system is now registering the fault in the airbag system)

Now turn the ignition off and close the door.

Now open the door again

Turn ignition on again until all dash lights are on but do not starting the Engine.

Now quickly press the drivers door interior light switch 7 times in rapid succession.

Now the air bag light SHOULD start flashing at a single rate ( the diagnostic system is now registering that the airbag circuit is now working correctly)

Turn the ignition off , and remove the key, now close the door.

Turn the ignition back on and the airbag light should go out after a few seconds.

Link to comment
https://www.sau.com.au/forums/topic/359321-rb26-conversion/#findComment-5739052
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • tylink720
      "Cheap" bolt on turbo on RB25DET NEO

      By tylink720 · Posted

      @Kapr Haha yeah thats the one. I missed that you had a built up engine, I wouldn't want to run it on there either then. It was good in my situation just to replace the original turbo on a stock engine. @MBS206Yep definitely not a replacement for anything name brand
    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
    • Watermouse
      "Cheap" bolt on turbo on RB25DET NEO

      By Watermouse · Posted

      https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • Kinkstaah
      Airbox for +T

      By Kinkstaah · Posted

      It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • GTSBoy
      Airbox for +T

      By GTSBoy · Posted

      By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
×
×
  • Create New...