Jump to content
SAU Community

Recommended Posts

The entire reason I started the post was because I'm not interested in building a RB24. I have searched for builds, and there are some out there, but if you bothered to read the post that I started, I clearly mentioned that I am not chasing a 2.4 Litre. The reason I started this build is that I wanted to know some information about whether the parts i mentioned would fit.

However I have found that skylines australia, is essentially a useless site, as it contains pretentious f**kwits like yourself, who believe they are gods, when they are merely little dicked faggots, with their keyboard warrior beliefs. As I'm a mech eng, i'm more than capable of working out the efficiency of an engine that is less than 3 litres and can thus make the conclusion that 3 litres will always ultimatly make more power than a lesser volume engine. This post was about what I had already, and what i can do with it.

Please block my IP address as I'm at an internet cafe, I won't be using again ;). I look forward to our next encounter, with my new account, at my new ip address. Look forward to more Bearforce1 top bloke.

Link to comment
https://www.sau.com.au/forums/topic/359709-to-r31nismoid/
Share on other sites

The entire reason I started the post was because I'm not interested in holding a BBW. I have searched for BBW's, and there are some out there, but if you bothered to read the post that I started, I clearly mentioned that I am not chasing a BBW just holding. The reason I started this is that I wanted to know some information about whether the penis i have mentioned would fit.

However I have found that skylines australia, is essentially a website, as it contains BBW Lovers like BOZ, who believe they are BBW gods, when they are merely giant little people, with their keyboard warrior skills. As I'm a little dicked top bloke, i'm more than capable of working out the efficiency of an penis that is less than 3 inches and can thus make the conclusion that 3 inches will always ultimatly make me frustrated and i will end up alone. This post was about what I had already, and what i can do with it.

Please block my IP address as I'm at an internet cafe, I won't be using drugs again ;). I look forward to our next encounter, with my new account, at my new ip address. Look forward to more Bearback faggotry.

Fixed!

Link to comment
https://www.sau.com.au/forums/topic/359709-to-r31nismoid/#findComment-5744048
Share on other sites

to op

suck multiple dicks homo

to r31nismoid.. <3 yewww :wub:

Hey Charizard

I could have a dick in each hand and one in my mouth and still not be as gay as you, <3 nismoid? f**kn top bloke...

Link to comment
https://www.sau.com.au/forums/topic/359709-to-r31nismoid/#findComment-5744086
Share on other sites

Guest
This topic is now closed to further replies.


  • Latest Posts

    • I purchased some (used but new to me) Yokohama A050 Mediums to try out for the first time and fitted them up to one of my sets of Rays TE Fortesst's. Sizes are 235/45R17 front and 255/40R17 rear. They are very chonky compared to the same sized AD09 on the same sized rim. Some fiddling will be needed to make them fit. How much camber do these like as a general rule? I imagine more than the rear camber of -1.5' I typically run. So my plan is to target -3.8 front and -2 rear
    • If you want to test it under temperature, I think you should enter the One Raceway day tomorrow with Duncan!
    • That looks great Mark!
    • Yeah yeah, the oven did get a good clean after the "baking"...LOL In other, wrinkle black painted stuff news, expansion tank and PS reservoir all fitted up and tested at temp Much nicer than the yellow stained plastics   
    • You now say stumble, but you said cut out before. Will it slow rev through the cut/stumble? What gap were your spark plugs set to when you them in?
×
×
  • Create New...