Jump to content
SAU Community

Recommended Posts

Nah wasnt me man, mines been off the road for the last few weeks. Had to fix a broken wheel stud and now im waiting for a set of brake pads to come in (hopefully will be here monday).

I havnt seen any R33's in Tbar that look like mine, mines pretty easy to pick,.Has black personalised plates "NIX250", chrome 18's (unfortunatly lol) and a twin tip exhaust cause i think cannons are for ships (No offence to the cannon lovers :P).

Edited by Nikk_666

Also i was thinking about putting up a spotted thread for Tbar area, but didnt no where to put it?

cause i saw a green R33 P plater with an odd bodykit near helidon, and also an orange series 2 33 in grantham.

Edited by Nikk_666

I see a couple of skylines drive past work each day. As for a a spotted thread we can just use this one, not really enough Toowoomba guys on here for the need for one right now

Least it will give us something to talk about :whistling:

Saw a matte black 33 with orange wheels/trim and HKS stickers on west the other day....

youll see a few of them on west during the week, all the uni students... i cant say ive seen a matte black one though. i saw a white 32 heading east on james on monday morning around 830.

Saw another 4 door r33, this one was a white pearl. Gonna give the 32 a wash, polish and vacuum on Saturday in preparation for Jambo next weekend. Who is keen to come and help me?

Saw another 4 door r33, this one was a white pearl. Gonna give the 32 a wash, polish and vacuum on Saturday in preparation for Jambo next weekend. Who is keen to come and help me?

I frequent bayside carwash of a saturday morning.

Always see a white 34 with top secret/z-tune front bar on west st near the uni. Think she's a GT

Saw another 4 door r33, this one was a white pearl. Gonna give the 32 a wash, polish and vacuum on Saturday in preparation for Jambo next weekend. Who is keen to come and help me?

yep gota get it looking good for jambo, im heading down on the saturday.

btw if anyones looking to get any graphic work done downs tinting (on james street next to the sex shop :P)

just did an absoutly amazing job with what i wanted made up.

yep gota get it looking good for jambo, im heading down on the saturday.

btw if anyones looking to get any graphic work done downs tinting (on james street next to the sex shop :P)

just did an absoutly amazing job with what i wanted made up.

Yeah gotta work tomorrow morning now so will have to do it Sunday. I'll be there both Saturday and Sunday, the 32 will be in the show and shine on the Saturday

Yeah gotta work tomorrow morning now so will have to do it Sunday. I'll be there both Saturday and Sunday, the 32 will be in the show and shine on the Saturday

Thats awesome man, might get to catch up with ya.

sooo how are numbers looking for the run on the 4th? (thats assuming we're still going ahead with it?)

One of the guys just informed me that the 4th is Father's day, so has been moved to the 18th, but there is a bit of interest from a few of the T'bar guys

Jamboree 2011 has been postponed until the 1st and 2nd of October... Lame

Yeah pain in the arse had the 32 all clean and looking pretty too, thinking about doing a little cruise on Sunday

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...