Jump to content
SAU Community

Recommended Posts

ENTRIES OPEN,

TIME TABLE

5:00PM GATES OPEN

5:30PM SCRUTINEERING

5:30 PM DRIVER SIGN ON

6:15PM DRIVER BRIEFING

6:30PM START TRACK ACTIVITY

10:30 PM END TRACK ACTIVITY

SPECTATOR

everybody is welcome to spectate at our events entry is FREE

we have an associate membership package available for spectators

costs $40 you get t-shirt, sticker, membership card & a free drink at all our events

you can apply for this on the day.

SCRUTINEERING

your car will need to pass scrutineering

brakes, brake lights, seatbelts/harnesses, windscreen wipers all need to work properly

drivers seat must be secured properly all wheel nuts must be present

you will need a secondary bonnet restraint if you dont have one just bring a short rope & the

scrutineer will assist you installing it

DRIVER/TRAINEE

to drive you will need appropriate clothing (non flamable)

your clothes must cover you from neck to wrists to ankles

closed shoes must be worn

and only helmets with the AS1698 sticker affixed can be used

COST

$50 if you want to learn to drift

$100 if your a member with driftmob & have a cams license

$120 if your not a member with driftmob & have a cams license

$100 for group bookings of 3 or more people for non members

$90 for group bookings of 3 or more people for members

we can issue you with a cams license on the day if you dont currently hold one

if you want to become a member you can apply on the day

HOW TO PAY

entrants can pay on the day but we recommend prepaying to secure a spot

at this stage we can accept cash & eftpos if you want to pay on the day

to be eligable for group discounts payment in full must be made for the number of people attending in that group

PREPAY

deposit total amount and bring your reciept with you on the day

no prepayments after 20th may

ACCOUNT NAME = DRIFTMOB INC

ACCOUNT NUMBER =259589

BSB =032372

BANK =WESTPAC

just a quick run down for the day,

we are track time orientated this means we will not stop for lunch

if you want to be a trainee/learn to drift for the day you will be permitted to sit as a passanger in any car roll cage is not essential

if you have any questions please ask but if its a noob question and somebody shoots you down its not my fault... LOL

cheers.

the driftmob crew..

  • 2 weeks later...

hey mate ,

the driver training basically entitels you to be a passanger in any car of your choice , it can be your mates or one of the driftmob cars

if you choose to ride in a driftmob car you will get pointers on key drift manouvers and have all your questions answered relating to drift

if your driving your own car you can ask for advise from one of the instructors on the night even get them to ride passenger with you

  • 2 weeks later...

wet skid pan is always a bit of fun as you can go four cars at once and all get nice and close its going to be some fun for sure....... if anyone wants some pointers come see one of the instructors dont be shy :thumbsup:



  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...