Jump to content
SAU Community

Recommended Posts

1989 R32 GTS4 Nissan Skyline 4 door

Odometer: 180,000 km

Reason for Selling: Moving to Melbourne NEED TO SELL ASAP

Engine:

rb20det

Garrett T03 turbo

k&n pod kit

FMIC

aftermarket Walbro 255L/hr fuel pump

aftermarket exhaust system with 3" tip

boost controller

new power steering belt

Nismo slave clutch recently installed

Suspension: Stock suspension

Interior:

Splitfire boost gauge

turbo timer

Sony Xplode head unit

Exterior:

Midnight purple colour

R32 stock front bar

Wheels & Tyres: Lowenhart 18" wheels, front tyres just been replaced

Extra Details: recently had car defected and all defected parts have been fixed, rear spoiler had to be put back on

Item Condition: vehicle is in reasonable condition with a couple of dints and scratches, interior is in GC

Needs fixing: Air conditioning belt and vents, castor rods, suspension is on its way out, oil leak from gasket, couple of dints that need tapping out and paint touch-ups, a few bubbles of rust starting to show. Don't have the time or money to fix these

Price and Payment Conditions: $5000 o.n.o. with rego

Looking to sell this car as soon as possible so open to negotiations

Contact Details: text or pm me 0416364469

IMG_02.jpg

IMG_01.jpg

Link to comment
https://www.sau.com.au/forums/topic/362247-1989-r32-gts4-nissan-skyline-4-door/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...