Jump to content
SAU Community

Recommended Posts

Heya all i own a nissan skyline r33 GTST thats done about 100000 miles.

Now i recently done a compression test with it at full operational temperture and all the cylinders was about 120 PSI.

This is very low obvioulsy and when i put oil in the cylinders the rise in PSI was about 5 to 10 PSI.

Also with engine running there is no blow back atall from the dip stick or out the oil cap best engine i felt before.

So with the no blow back and only a max of 10 psi rise with wet compression test which means its still bout 20 to 30 PSI off a decent engine PSI i belive it has to be the valves.

Any input or experince from you guys would be great i just find it weird that all cylinders are evenish and it to be the valves thought they would be uneven if valves leaking.

Cheers :).

Link to comment
https://www.sau.com.au/forums/topic/362905-compression-test-results/
Share on other sites

If it still puts the power down, as said above, I wouldn't jump into the rebuild right away... Enjoy her. Ive seen a few RB's with 180000+kms still unbuilt and still making nice power. Seriously, until its something major, or you plan to do some big performance upgrades, there is no point. When you do the rebuild you replace everything anyway, you don't reco it.

not had power test i dont think it pulls as hard as my last skyline thou and yea im still gonna use it just if it was just the valves thats nice and easy to take head of and regrind them and wouldnt mind doing that :) and i see as machining the head as hiding the problem really not dealing with it lol . gonna take rocker breather pipe off from inlet when get round to it see if it breaths heavy then or throws lots oil out due to its burning alot oil that could be the turbo thou .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...