Jump to content
SAU Community

Recommended Posts

In anywhere between 2-4 weeks I'm going to be a dad (like baby's ever come on time anyway).

I have an R33 GTS25t and was wondering if a baby seat / newborn capsule will fit in it, as they are a 4 seater and I thought the capsules / seats had to go in the middle???

BEFORE anyones asks... yes I do have the child seat restraint bolt things in the rear parcel shelf.

Do I need any special brackets, etc, to mount the seat / capsule on the side rather than the middle?

Are the any laws prohibiting me from putting the seat / capsule on the side?

LASTLY: Has anyone got / had a good capsule / seat that they have had fitted to their skyline and can recommend?

Thanks for all the helps peoples... I'll await the abundance of replíes :rofl:

Link to comment
https://www.sau.com.au/forums/topic/36299-calling-all-parents/
Share on other sites

Firstly, Congratulations!! You'll never look back from here... Being a father of 3 boys aged 7, 3.5 and 0.75 I can honestly say they bring more joy than most anything else in this world...

There are no laws against putting a baby capsule / seat on the side as opposed to the middle... You may find that the clearance when using a capsule requires you to move the seat quite a way forward though... It may be best to use the passenger side for this reason...

No special brackets should be required if you have all 3 child restraint bolts in the parcel shelf... You may find that the baby seat / capsule leans to one side a little when used on the side though due to the hump in the middle of the rear seat... A folded towel underneath the baby seat evens things out...

I'd recommend that you get a convertable baby seat / capsule... ie one that can be used as a baby capsule in the early months and then "stood up" once the child is old enough to sit up... I use and can recommend the Fisher Price baby seat / capsule... It's lasted over 3.5 years of continuous use for my kids and is still going strong... Well made and very comfortable for the children.

Hope this helps!!

buy a Recaro Baby Seat

Hey that's what i did! To match the GTR interior. Good Luck, & wish you guys the best, we just had out first child a baby boy who's now 9weeks old. Regarding the seat, I didn't have any problems fitting in the GTR, just got one of the RACV guys to fit it. No headaches for $35.

Congrats on the imminent arrival. :rofl:

I'd echo the comments on getting a combined capsule/seat. If you are going to buy one this is defiantely the go as you'll only need to fork out for the one seat until they get to 2 1/2 years old or so.

We've got one that fits well in the back of the 33. I'll have a look at the name/model tomorrow and post it.

You may find there is a company that comes to the hospital one day per week and fits/rents/sells seats and capsules. That's what happens up here anyway.

Congrats, and I hope all goes well with the birth.

I think one of the main reasons for putting the baby in the middle seat, is that there is much less chance of injury in the event of a side impact.

However, if you do decide to use a seat next to the door, please make sure you use the passenger side..... it makes my blood boil when i see parents lifting the capsule out of the car, and swinging it towards the traffic while they shut the door.

:cuss:

Thanks peoples :D

I thought I'd get laughed at... of well I guess people actually care!

I've only got 2 child anchorages in the back of my R33... am I meant to have 3? Does the 3rd one really matter?

geez, I'd love to spend $600 on a recaro baby seat, but bottom line is, i'd be the most expensive thing in my car and something else to go missing the next time it gets broken into :rofl: Plus, I really don't think the kid is going to mind whether or not it is sitting in a plush recaro seat, or a 'yum cha' equivalent (please note: I'm NOT being racist... I first heard that expresion of an asian friend of mine!)

The only thing a recaro seat is going to do that a fisher price seat won't is REALLY hurt my bank account! :)

Thanks for all the input once again!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...