Jump to content
SAU Community

Recommended Posts

Hey all,

I noticed today morning when i parked the car, my idle was a bit high - this happened about once or two before but nothing since. On my drive home today from work, everything was fine and then my stagea started to lose acceleration pretty consistently. It happened at no particular RPM range, either on or off boost. She'll be going nicely and then it feels like i just took my foot off the accelerator, but i'm still pressing it! no squealing belts, choking or misfiring.

I'm wondering if AFM could be causing this? but i had it cleaned during my last service at xspeed and haven't really had this issue.

I have a greddy infometer plugged into the OBD port, i noticed the following the AF/C reading is showing 104% - 118% and when the drop happens it goes down to 97%. (a bit high but does anyone know if the greddy infometer 1's displayed this correctly?). I can also see voltages, but i dont know whats normal voltage for a AFM.

Don't think it could be the battery, as it didn't completely shutoff the engine. its an odd one! now i have to figure this out so i can drive to work tommorow.

does anyone have any ideas regarding the above?

thanks

Link to comment
https://www.sau.com.au/forums/topic/363664-weird-issue-with-my-stagea/
Share on other sites

cheers for the reply shetlander, i cleaned out the AFM this morning with some contact cleaner - no protective mesh on the front and back of the AFM though, was your stag's AFM like this? parked the car and the idle was up around 1400RPM while in park. turned the engine off and back on again and it was normal (~650rpm)and didnt repeat.

however drove ok into work this morning no drop outs in acceleration, i monitored the voltages with my greddy infometer:

1.20volts (+/- 0.01v) with A/Cond off

1.31v(+/- 0.01v) with A/Cond on

peak voltage: 3.02v

ranged between 1.4-2.8v during driving.

Does anyone know if these voltages are within operational spec?

Also the infometer showed a diagnostic code of "1", but that doesnt relate to any codes that i know of. This could be a lost leader, as I dont know if the greddy infometer v1 can get the DTC fault codes from the stagea ECU. its currently set to Nissan-non obd, wont connect otherwise.

thanks

Edited by Scratch

Vacuum leak. But because your car isn't running like crap? the air is being metered. The 2 things to check are the Idle Contol Valve, and the Cold Start Valve.

Both of these valves get gummed up with crap over time causing them to stick open and cause high idle.

Search for the DIY tutorial on this forum on how to clean your AAC idle control valve. The cold start valve isn't covered in that tutorial but it would be worth cleaning as well. On the S1 I believe it is located under the intake manifold.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello First, I apologize if this is not the correct forum. Let me know and I will move it to the correct one. I'm having a problem with the tachometer on my Skyline R33 with an RB25DET Neo engine. I'll tell you from the beginning. I'll tell you from the beginning. I have the RB25DET Neo engine installed in a Nissan Patrol GU, with a Link G4X control unit specifically for that engine,  and I have fitted a Skyline R33 tachograph to the original GU dashboard, but it doesn't work properly. I have the tachometer connected to the positive and negative terminals of the GU panel's wiring, and the signal cable is connected directly to the ECU output pin, but the rpm fluctuates widely. Can anyone tell me if the output signal from an R33 ECU is the same as the output signal from an R34 ECU, or if the voltage and signal type are different? Regards and thanks.  
    • I guess it was the thought about "Oh if I were to drive this everyday". Then no, SL500 I wouldn't really consider lmao. 
    • Yeah actually really fair point. Idk what I was thinking when looking at the SL500. Now that I think about it, I feel like I would have more enjoyment out of a shitbox that I would need to repair than some fancy merc. Although I must admit the SL500 does look quite nice. My bad hahaha.
    • 100% Also "Not wanting to spend money" is THE WORST IDEA IMAGINABLE when coming to a project car of any kind. They EXIST to BURN MONEY. Sure, gas money is a thing. A stock car with the worst fuel economy ever sold would probably be cheaper than modifying a car with FREE petrol for the life of your ownership of it, lol.
    • Amount of time you're being observed by law enforcement is so minute, that you could be a dumb shit 90% of your driving time, and never lose a demerit. You could also be the best driver ever and still get hit with a fine.   When you realise how quickly everything turns from "Wee, we're having fun!" To "oh f**k oh f**k oh f**k", you start to realise the only way to be a good driver, is to not be doing anything dumb or unexpected by normies on the road. You want to go fast, go to the track. Someone there in a 1990s slow POS will also show you how bad of a driver you are as they lap 10 seconds per lap quicker than you can in a car that should be considerably faster.
×
×
  • Create New...