Jump to content
SAU Community

Recommended Posts

1989 R32 Gts-t Type M.

ENGINE: rb20det rebuilt ( recipts ) front mount resprayed non gloss black with hard pipe kit, turbosmart bov, 3" exhaust hi flow 3" cat, microtech lt-12s comes with hand controller, direct earth wiring kit, R34 series one turbo, boxed pod, also have highmount manifold, 38mm tial gate, 3" dump to suit high mount.

DRIVELINE: brass button clutch, 4.3 diff locked, short shifter,

SUSPENSION : nismo adjustable shocks, unknown springs ( red ), kkr adjustable castor rods, new tie rod ends.

BRAKES: factory type m brakes with new pads and been painted vht blue.

EXTERIOR: resprayed unknown blue inside & out except engine bay, gtr front bar with lower n1 lip, factory type m side skirts, type m rear pods, stock type m wing or n1 boot lip, Work VS - Edition 17x8 +30, 17x9 +35 comes with all centre caps, tinted windows,

INTERIOR: all factory Gts-t, besides autotechnica wheel, drift shift knob, greedy ext temp guage, drift boost guage ( not installed ) monsta tacho with oil temp oil pres, shift light, no head unit or speakers,

Odds & ends:

Spare 16x7+30 hinodex wheels good tyres.

Spare Rb20det head.

Spare R32 gtst taillights.

Alloy catch can.

R32 gtr front bar n1 lip genuine, R32 gtr fiberglass copy.

N1 boot lip.

Stock rb20 turbo.

Stock intercooler.

High mount manifold.

Tial 38mm gate.

New drift boost guage, and cup

New drift gear knob.

H.I.D. kit like new.

Short shifter.

Other shit like r33 lcas.

Probaly more.

The bad:

Running rough been told it could be because of the 34 turbo recently fitted needs some nipple welded into intake or something because of different wastegate setup.

Car has dent in drivers door and sill from previous owner have spare door and the side skirt covers sill damage :P also from previous owner rear pillar has been hammered

No rego.

Can come with blue slip!

Has custom plates EVL.32R

Dash says 97,000 k's but import papers say 127,000 k's so obviously been changed.

Car is located in singleton nsw locked away in a shipping container. Havent even driven it just bought it and stored it away.

Im intersted in swaps for a regoed import, or xr6 ute, 4x4 etc

$6500 ono with blue slip!

0432163488 jahn

Will have pics up as soon as i have acess to a computer for now msg my fone and ill send some thru cheers!

Link to comment
https://www.sau.com.au/forums/topic/364089-r32-gts-t-type-m/
Share on other sites

OK UPDATE! The 32 is running fine the solution you ask? I had the microtech lt-12s pluged in and it wasnt tuned for the internal wastegated low mount setup. Plugged the stock ecu in and she runs like a pearler!

So all she needs is rego and your on ya horse!

Also have a vp commodore 5 speed wagon in immaculate condition all standerd besides tinted windows and sports ryder rear swaybar. And a ford laser tx3 1.6 n/a fwd 14" meshies.

Will swap all 3 for something if anyone is intersted

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...