Jump to content
SAU Community

R34 Xenon Headlights

jimtron4000
 Share

Recommended Posts

jimtron4000 Collaborator

jimtron4000

Posted
Posted

For sale are a pair of r34 xenon headlights. Both are in working condition however:

The drivers side one has a melted lens in front of the high beam (didn't realise that was possible). Otherwise in near perfect condition.

The passenger side one has been getting moisture inside of it (judging by the silicon around it around there's been previous attempts to seal it up). Other than the moisture and the siliconed up bits, this headlight is in perfect order too.

Both headlights are still in my car, but will be removed when i find a new pair. They also have "eyelids" attached... I've not yet looked at how they're attached and whether i'll be able to take them off. Once they're off i will dry out the wet one and seal it up properly, so pretty much that one will be good to go. The drivers side one would suit a Xenon conversion i guess... if the lens was replaced (or fixed?) it would be fine.

These will not be available straight away but I'm pretty keen to get replacements asap so these should be available real soon.

I think i have to give a price, so i'll say, ummmmm...... $500 for the pair??? Just make an offer hey?

I'll get some pics up soon.

They're located in Melbourne.

Link to comment
https://www.sau.com.au/forums/topic/364977-r34-xenon-headlights/
Share on other sites
jimtron4000 Collaborator

jimtron4000

Posted
  • Author
Posted

I'll get some tomorrow. The melted one looks normal, except for a patch about the size of 2 50c coins in front of the highbeams which is all white and melted looking. The passenger one looks normal except that it has moisture in it at the moment, and the bit where the lens and the backing attach has been siliconed up, and there's silicon around the backing of the Xenon. Pretty much the back looks normal except that you can tell that there have been attempts to seal it up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Quieter performance exhausts (or muffler add-on options)

      By Murray_Calavera · Posted

      Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • f00stx
      Quieter performance exhausts (or muffler add-on options)

      By f00stx · Posted

      So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...