Jump to content
SAU Community

R32 Heavy Steering


040122
 Share

Recommended Posts

My r32 recently became very hard to steer, the steering wheel will not centre once let go either, i checked the power steering fluid and it is not dropping in fluid level at all. the steering is heavy as soon as the car is turned on. can anyone help me please?!?

Link to comment
Share on other sites

There's a good chance you have suffered the same problem that I had on my R32 a few years back. The wiring loom for the oxy sensor heater shorted, killing the oxy sensor and coincidentally killing the power steering. Took a bit of finding.

Link to comment
Share on other sites

There's a good chance you have suffered the same problem that I had on my R32 a few years back. The wiring loom for the oxy sensor heater shorted, killing the oxy sensor and coincidentally killing the power steering. Took a bit of finding.

try checking the hicas fuses too, hicas is linked with power steering

-D

Link to comment
Share on other sites

hey have you found out what the problem is yet?? my 32's steering has become HEAVY over night whilst losing no power steering fluid, mechanics suggested either rack or pump, any suggestions??

Link to comment
Share on other sites

there is a speed sensor somewhere in the dash , my brother just went through this and i am now experiancing the same prob replaced the sensor and now runs fine

its a steering angle sensor and its located in the steering column

the speed sensors are located on each wheel

-D

Link to comment
Share on other sites

hey i just noticed im missing a belt but im not sure what it is, there's the belt on the far left which is fan belt i think, then the middle belt which is power steering, then down the bottom on the far right bout where the intercooler and air intake box are theres pulleys for a belt but my belt is missing, anyone know what this belt is ??

Link to comment
Share on other sites

Pretty sure the speed sensor for a r32 is at the back of the dash, connected to the speedo cable. If you've had the dash out recently there is a chance that it wasn't clipped in properly. Having said that, if your speedo is working it's probably not the case.

Link to comment
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Me too. Apparently the new version of Invision will allow some customisation so look forward to a 'Love' reaction and a new 'Like' icon.
    • Which injectors are you using? It's likely the fuelling is off also, so as above.
    • Awesome to know. I have a Series 1, and When pulling my front bumper off for the first time i realised my reo/crash bar was a bit worse for wear, and was going to try pick up a better one soon just so i can replace it. Someone is selling a full series 2 front bar and brackets for a decent price, so was going to probably reuse my brackets and install the new second hand reo/crash bar. I also have a genuine Altia body kit to do up, spray and put on, and not sure if that will use the series 1 or series 2 brackets for the front bumper, so having both will be handy, and knowing i can drill holes out to make stuff fit between series is also handy to know!
    • I should also say that the while they are different the only parts that matter are the center headlight supports and center bar from S1 to S2. The center bar will work, but the S1 has holes that clips go through into the S1 bumper. So if you were super cheap you could simply drill the S2 bar. Same thing with the side/wings. They have slightly different 'clips' but can be made to work. The center headlight brackets however, cannot. This is also where the GTR differs, which has a different center bar, and different headlight supports (to either GTT system), it also has different 'wing' headlight supports which is what I am calling under the headlight. However those CAN be made to work with the GTT Reo for a GTR front bar by a small spacer and a drill/tapping a thread into the reo because the bolt positions are slightly different. So people only really need the center brackets to go between GTT S1, GTT S2, and GTR if you are happy to do some tinkering.
    • Indeed  😃  Appears the site is back up now (migrated not updated) - kudos @funkymonkey & @PranK
×
×
  • Create New...